Therefore, do not leave them for a long time in the car. • New discs may have Ball-point pen some roughness around the edges. If such discs are used, the player may not work or the sound may skip. Use a ballpoint pen or the like to remove any roughness from the edge of the disc. Roughness • Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. • Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try t

Doing so may damage it and voids your warranty. • Keep drinks and drops from umbrellas away from the set. Water may damage the internal circuitry. • Do not let the set become hot. If temperature in the car is high or the set has been exposed to direct sunlight and is hot, lower the temperature before using it. (The liquid crystal panel will work properly within a temperature range of 41° - 104° F.) muaisiuiiiuziu • In extremely cold temperatures, the movement of the picture may be slow and t

(see Mounting Description on page 7) . IR TRANSMITTER SPECIFICATIONS General Specifications Power Requirement: 12 volts dc Power Consumption: 1 watt, Power On Dimensions ( w x h x d): 3.75 x 1.89 x 4.72 in. Mounting Base (95 x 48 x 120 mm) Mounting Holes: 3.86 in. (to centers) (98 mm) Supplied Accessories: (2) M4x12 Sheet Metal Screws, (1) 5-pin Power/Channel A (1) 3-pin Channel B Molex (2) Plastic Screw cover Figure 1. The WH200 Transmitter descriptions. WH200 DUAL CHANNEL INFRARED HEADPHONES W

• Activating Bluetooth® Transceiver pairing mode 1. Turn on the Transceiver by powering up the car audio system, note that the Red LED blinks once every 5 seconds to confirm that the power is on. 2. Press and hold the [ ] and [ ] buttons simultaneously for 2 seconds or longer to activate Bluetooth® pairing mode. Note: • If no device is paired to the Transceiver after 3 minutes, pairing mode will be cancelled. For more information on Bluetooth® pairing, please see chapter “Pairing Sequence” on pa

To ensure the best performance of your system, please read this manual carefully. EXPLANATION OF CONTROLS: (Fig. 1) Infrared Transmitter: 1. Infrared Emitting Leds - Transmit signal to headphones Headphone Receivers: 2. Infrared Sensors - Receive signal from the transmitter 3. Battery Cover 4. Volume Control 5. Power Switch 6. Power Indicator Led 7. Auto ON/OFF Micro Switch BATTERY INSTALLATION: (Fig. 2) 1. Place two (2) alkaline AAA batteries into the battery compartment of the Headp

Use of such discs will cause misoperation or damage. Do not expose compact discs to direct sunlight or any heat source. Note: • Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may get caught in the internal mechanism and damage the disc. 6 DRB4675/DRB3S75/RDB465D/R0B365D 6. DCP (Detachable Control Panel) The control panel can be detached to prevent theft. When detaching the control panel, store it in the included DCP case to prevent scr

All Rights Reserved. Copyright © 1998: Clarion Co., Ltd. PE-1637B 1999/1 (A·C) Printed in China / Imprime en Chine / Inpreso en China 280-7231-00 Thank you for purchasing the Clarion ARX8570z. * Please read this owner’s manual in its entirety before operating this equipment. * After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). * Check the contents of the enclosed warranty card and keep it carefully with this manual. * This manual includes the operating proc

Solid Expressions of Power, Streamlined for a Single SERIES Purpose - High Output to Drive Your System CLASS GH/AB AMPLIFIERS XH7110 MONO CLASS GH POWER AMPLIFIER XH5410 4/3/2 CHANNEL POWER AMPLIFIER CEA 2006 Power Ratings 100W x 4 RMS [4. @14.4V .1% THD+N] S/N 86dB (Ref: 1W into 4.) Class GH and AB Models Precise Frequency Selector BC2 (Optional Wired Remote Bass Control) . Remote Control for XH7110 Amplifier CEA 2006 Power Ratings 460W . 1 RMS [4. @14.4V .1% THD+N] S/N 68dB (Ref: 1W into 4.) P

Setting the Jumpers and Switches MS8200 / MS8300 Installation Manual -Page 13 Remote Transmitters Using the Remote Transmitters Button 1 Button 2 Mode Button LED Each system comes with 2 Remote Transmitters, pre-programmed to Arm and Disarm the system withchirp confirmation using Button 1. The Mode Button will change function of both Button 1 and Button 2 each time it is pressed. When the Arm/Disarm Button is pressed together with any other Transmitter Button, the systems Chirp confirmation sett

1. Press the [RDM ] button. “RDM ” lights in the display, an individual track is selected randomly and play begins. 2. To cancel the random play, press the [RDM ] button again. “RDM ” goes off and normal play resumes. DB168R/BD169R/BD169RG 9 English English 6. SPECIFICATIONS Radio section Tuning System: PLL synthesizer tuner Receiving Frequencies: FM : 87.5 to 108 MHz (0.05 MHz steps) MW : 531 to 1602 kHz (9 kHz steps) LW : 153 to 279 kHz (3 kHz steps) CD player section System: Compact disc digi