NEVER under any circumstances insert such a plug into a 13 amp socket. 2 NEVER under any circumstances use the appliance or mains lead without the fuse cover fitted. This is the little cover fixed into the base of plug to hold the fuse in place. 3 If you lose the fuse cover then please contact any electrical dealer for a replacement or ring our helpline. 4 A replacement fuse must be rated at 13 amp. These must be manufactured and approved to BS 1362. 5 IF IN ANY DOUBT PLEASE CONSULT AN ELECTRICI

Please retain for future reference SAFETY OPERATING INSTRUCTIONS PLEASE READ BEFORE USE . ALWAYS CHECK PAINT MANUFACTURERS THINNING INSTRUCTIONS BEFORE PROCEEDING. . ALWAYS CHECK PAINT MANUFACTURER’S INSTRUCTIONS FOR SURFACE PREPARATION. . ENSURE PAINT IS STIRRED THOROUGHLY BEFORE USE. . Never use corroded or damaged batteries, do not mix old and new batteries. . Do not overfill the paint reservoir. . NEVER use any liquids other than those specified. . Always ensure motor housing is firmly clipp

2) When you get to the end of the line, release the Trigger for a moment and then apply the product in the opposite direction just beneath the line you have sprayed. 3) Next, to achieve a vertical strip adjust the Spray Direction Plate (4) to the horizontal position then pull the Trigger and move your arm up and down over the horizontal strips you just have sprayed. Through gradual movement of the Spray Direction Plate (4) between Horizontal, Vertical and Round spray pattern you can vary the wid

Please retain for future reference. 2 EXPLODED PARTS VIEW 13 14 14 13 Fig.2 12 11 10 9 7 8 4 5 6 2 3 1 A B Fig.1 Fig.3 HV3500 HV2900/ 3900 PARTS LIST FFiigg..11 No.Description Part Code No.Description Part Code 1. Needle and Fluid Tip Tool V0018 7. Fluid Needle 2.0mm V0006 2. Air Cap Ring V0001 8. Lip Seal -Fluid Needle V0007 3. Air Cap V0002 9. Paint Flow Adjuster V0011 4. Spray Direction Plate V0003 10. Paint Container Seal L0682 5. Fluid Tip 2.0mm V0004 11. Pick-up Tube V0012 6. Fluid Tip O-R

Refer to the chapter on cleaning to see how the Fluid Tip and Fluid Needle can be removed and switched for a smaller/larger Fluid Tip and Fluid Needle assembly. • Fill the Paint Container with the product to be sprayed. Stir well (as mentioned above). • Screw the Paint Container to the base of the Spray Gun and tighten accordingly. • Unroll the motor unit air hose and attach it to the back of the Spray Gun. • Unroll the power cable and attach the plug to the mains supply. • Switch the Spray Stat

The round spray is used for small objects or for areas - such as corners – that are difficult to reach. To adjust the spray pattern, loosen the Air Cap Ring (1), adjust the position of the Air Cap (2) to obtain either a vertical, horizontal or round pattern then re-tighten the aircap ring. PAINT VOLUME The volume of paint sprayed is easily adjustable. (Fig.5(a)) Completely close Fluid Adjusting Screw (8) by turning this clockwise as far as it will go. Whilst pulling the trigger, begin turning th

! Ideal for removing paint in awkward corners, crevices, mouldings, beading or architraves. Concentrator nozzle G84 Glass protection nozzle -G89 ! Deflects the heat away from glass or other fragile areas. ! Ideal for windowsills, ledges, frames and skirting boards. Glass protection nozzle G89 Hook nozzle -G87 ! Disperses the heat flow evenly around the whole work surface. ! Ideal for defrosting frozen pipes, soldering pipe work, bending plastics or heat shrinking electrical insulating tubing. G8

These tools are illustrated on page 3. Pure Steam does not require detergents, chemicals or other cleaners, it cleans naturally with the action of steam. This powerful action also removes any traces of powder or liquid cleaners or detergents that have been previously used. SAFETY CUT- OUT A safety cut-out is fitted to prevent overheating of the element if water boils below the min. level. If unit stops boiling during use this may be the cause. Wait for 2 minutes before removing filler cap then r

Fit the strap hooks into the round holes at the top of the Spray Pack. ii. Feed the strap through the vertical slots at the bottom of the Spray Pack, loop around and feed back through the strap buckle. Spraying IT IS RECOMMENDED THAT THE UNIT IS TESTED WITH WATER PRIOR TO EACH USE 1. Remove Spray Pack Lid (2) and pour in required spray material and thinners. 2. Ensure the spray material and thinners do not exceed the max fill line on the Spray Pack. 3. Fit the Spray Pack Lid, ensuring that Seal

2. Pour any residual material into its container so that it can be used for the future. 3. Pour a quantity of the respective thinner into Container, shake the gun lightly, reassemble the gun, then spray this liquid through the gun. Repeat this until the thinner being sprayed is coming through with no traces of paint. 4. Clean any traces of paint off the outside of the gun. 5. Clean the Paint Container Seal (12) inside the gun body. 7 L0553 (04-08) (US-FR-ES).qxd 20/6/08 2:25 pm Page 8 L0553 (04-