and ULC.S629 (650°C) for Canada. . This wood burning unit is only listed for installation with 6.0” diameter chimney connector and chimney systems. Installing this unit on prefabricated chimneys larger than 6.0” diameter will result in decreased draft and the potential for poor unit performance. . Follow all venting system manufacturer’s installation requirements and required clearances. . Use three sheet metal screws at each single wall chimney connector joint (check manufacturer’s recommendati

• Before using an existing chimney, be certain it is in good condition (A chimney sweep inspection is highly recommended). Also, make sure the chimney meets the minimum standards listed in NFPA 211 (A chimney professional can confirm this upon inspection). • If connecting this stove to a factory built chimney, it may ONLY be a 6” flue, UL103 HT venting system. Connection to any other factory built chimney may result in a poorly operating or dangerous stove installation. • When connecting to an e

If you need to place your unit closer it will require wall protection. There are many wall board manufacturers, and most require a one inch (1”) air space between the wall and the board. You can place your unit within twelve inches (12”) of some boards and reduce your clearance by two-thirds. In addition, the wallboard only needs to be six inches (6”) higher than the top of the stove; by placing the unit twelve inches (12”) from a combustible, the flue pipe will be closer than eighteen inches (1

If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have been thoroughly cooled. Page | 23 DAILY MAINTENANCE DAILY MAINTENANCE Ash Removal and Disposal • Press the “Off” button and allow the stove to complete the shut-down cycle and cool completely. • Grasp the heat exchange cleaning rod located at the middle of the decorative room air grill and repeatedly pull it in and out until ash stops falling from

Resizing with a stainless steel liner may be required. 11. It is recommended that no more than two 90-degree bends be used in the stovepipe installation. More than two 90-degree bends may decrease the amount of draw, and possibly cause smoke spillage. 12. A damper is not required in this installation. Remove the damper plate in the chimney or secure it in the OPEN position. 13. Single wall flue pipe assemblies must not exceed 10 feet in overall length. CHIMNEY REFER TO CHIMNEY AND CHIMNEY C

(AC-3100 for 4000+ ft. installations.) Must have minimum 3” adapter before tee for longer run. For shorter run (such as Masonry Connection below), tee alone is acceptable. Basement Installation should be performed by professional installer. Use 3” metal pipe and coupler for Outside Combustion Air. Minimum 3’ clearance from ground to the Pellet Vent Exhaust Pipe. Illustration 1 Freestanding Pellet InstallationCaution: Follow the pipe manufacturer’s installation instructions and directions for pas

Box 206 Monroe, VA 24574 Phone: (800) 516-3636 Fax: (434) 929-4810 Installing the PU-DTSTAT BEFORE BEGINNING THERMOSTAT INSTALLATION BE CERTAIN THE STOVE IS UNPLUGGED AND COMPLETELY COOL. DEPENDING ON WHICH STOVE THE THERMOSTAT IS BEING INSTALLED ON, THE CONTROL BOARD MAY NEED TO BE REMOVED FOR INSTALLATION. 1. Using a small, slotted screwdriver (often referred to as a jeweler’s screwdriver), loosen the two screws on the front of the J18 thermostat terminal, shown below and remove the jumper

• The firebox baffle is a free floating design, which reduces thermal stresses on the baffle and makes it easily removable for cleaning. • Remove the baffle by: o Grasping the baffle lifting tab in the center of the baffle. o Tilting the baffle towards the back of the stove. o Lifting the baffle up and out of its support holes on the firebox shelf. o Allowing the baffle to slide down to the cradle and then tilting it down and pulling it out of the stove through the main loading door. • As soon a

This paint can be ordered from your local dealer or from the factory. E. Blower System (Part #AC-17) The blower system for this unit is placed under the ash lip and moves air under, around and finally exits over the top front of the stove. This blower should be removed and cleaned at least once a year; you can use a vacuum cleaner to remove any loose dust build-up, but do not disassemble the blower. This part has sealed bearings and does not require any oil. F. Glass Cleaning Even though this st

Visit our web page at for helpful information, frequently asked questions, parts & accessory orders and more. NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489. CAUTIONS AND WARNINGS: READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION CAUTION: This unit must be installed in accordance with these instructions and must comply with local building and fire codes. Failure to do so could result in a chimney or house fire, property d