Service or maintenance performed by unqualified personnel could result in a risk of injury. 24.,When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. USBOOS-l Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2. Accessories must be rate

For model 9556NB, mount the inner flange onto the spindle so that the side of the inner flange with the 20mm diameter protrusion faces the diamond wheel. Place the diamond wheel onto the inner flange making sure the protrusion fits into the arbor of the wheel. Use the lock nut to secure the wheel by placing it on the spindle so that the flat side faces the wheel and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then

A list of the Factory Service Center locations and phone numbers is provided on page 24 for your convenience. 21 LIMITED WARRANTY - California Only - Makita U.S.A., Inc. a distributor of utility and ¡awn and garden equipment in the U.S., warrants to the owner of 1995 and later utility and/or lawn and garden equipment engines that the engine 0) has been designed, built, and equipped at the time of manufacture so as to conform with the applicable regulations of the California Air Resources Boa

Chainsaws with significantly reduced kickback potential are available. STIHL recommends the use of STIHL reduced kickback bar and low kickback chain. Advertencia! Esta sierra es capaz de causar contragolpes severos, los cuales pueden causar lesiones graves o mortales. Solo es apta para usuarios con necesidades extraordinarias de corte y mucha experiencia y capacitacion en el manejo de los contragolpes. Existen sierras con un potencial mucho menor de causar contragolpes. STIHL recomienda usar una

Don't force small tool or attachment to do the job of a heavy-duty tool. Don't use tool for purpose not intended. 7. DRESS PROPERLY. Don't wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair. 8. USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. caoutchouc et les chaussures anti-dérapantes sont conseillés si vous travaillez de

When the tree hangs or for some other reason does not fall completely, set the saw aside and pull the tree down with a cable winch, block and tackle or tractor. If you try to cut it down with your saw, you may be injured. Sectioning Method WARNING! Felling a tree that has a diameter greater than the length of the guide bar requires use of either the sectioning or plunge-cut method. These methods are extremely dangerous because they involve the use of the nose of the guide bar and can result in k

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the switch lever is in the neutral position, the switch trigger cannot be pulled. Selecting action mode Rotation with hammering (Fig. 4) For drilling in concrete, masonry, etc., depress the lock button and rotate the change lever so that the pointer points to the H symbol. Use a tungsten- carbide tip

SPECIFICATIONS Model 2012NB Cutting width 304 mm (12”) Max. cutting depth 3.0 mm (1/8”) of stock width less than 150 mm (5-7/8”) 1.5 mm (1/16”) of stock width from 150 mm (5-7/8”) to 240 mm (9-1/2”) 1.0 mm (3/64”) of stock width from 240 mm (9-1/2”) to 304 mm (12”) Feed rate /min 8.5 m (27.9 ft.) /min. Table size (W x L) 304 mm x 771 mm (12” x 30-3/8”) No load speed (RPM) 8,500 /min. Dimensions ( W x L x H ) 483 mm x 771 mm x 401 mm (19-1/64” x 30-3/8” x 15-25/32”) Net weight 27 kg (59.5 lbs) •

MAC700 MAC2400 MAC5200 Horsepower 2 2.5 3 SCFM @ 40 PSIG 3.8 4.8 6.9 SCFM @ 90 PSIG 3.3 4.2 6.5 Cut-In Pressure 100 PSI 100 PSI 110 PSI Cut-Out Pressure 130 PSI 130 PSI 140 PSI Bore 47 mm 51 mm 47 mm Stroke 44 mm 44 mm 44 mm Voltage -Single Phase 120 120 120 Motor RPM 1720 1720 3420 Amperage @ max pressure 12.4 12.3 13.8 Tank Size 2.6 Gallon 4.2 Gallon 5.2 Gallon CSA/US Listed Yes Yes Yes SPECIFICATION CHART Minimum Circuit Requirement: 15 AMPS * A circuit breaker is preferred. Use only a fuse o