Other connections are possible, but they require additional fittings (see Section B on page 4). The Polaris 380 is intended for use with a Polaris Booster Pump.You should have a licensed electrician install the cleaner’s booster pump. The booster pump must be installed according to the electrical codes applicable in your area. Improper installation can result in serious or even fatal injury. The following are important points to remember when installing and operating the Polaris 380. • Always tu

Single-wheel sideSweep Hose • Clean the skimmer, filter and pump basket, clearing debris that restricts water flow. • Check the hoses, connections and swivels for leaks that cause loss of water pressure. • Remove the blue restrictor disk from the UWF. • If an adjustable gate valve is installed on the booster pump or cleaner line, open it completely so water can flow freely to the Polaris. If count is more than 32 RPM: • Replace the blue restrictor disk in the UWF with the red restrictor. If the

Мы уверены, что Вы будете довольны приобретением нового изделия нашей фирмы Перед началом эксплуатации прибора внимательно прочитайте данную инструкцию, в которой содержится важная информация, касающаяся Вашей безопасности, а также рекомендации по правильному использованию прибора и уходу за ним Сохраните инструкцию вместе с гарантийным талоном, кассовым чеком, по возможности, картонной коробкой и упаковочным материалом I, Общие указания по безопасности • Прибор предназначен исключительно д

: PED-010 REVISION: 1 EFFECTIVE DATE: 08-24-2004 POLARIS SERIES TBM 200 LH ( 8” ) TYPE PHO / PBO / PVO ELECTRO-SUBMERSIBLE PUMP PUMP TYPE: _TBM 200 LH ( 8” ) TYPE ( ) POLARIS PART NBR.: _700.200.05. HP / V / Hz / Poles: / / / INSULATION: F □ H □ SUPER EXPLOSION PROOF: Y □ N □ EQUIPMENT OPTIONS: POWER CABLE: ADDITIONAL (FEET) VITON MOTOR O-RINGS □ VITON SEAL ELASTOMERS □ “SEAL GUARD” □ “SLURRY BOSS” □ “MOTOR SENTRY” □ SS MOTOR FLANGE □ COAL TAR EPOXY □ PUMP SERI

• New plumbing lines should be flushed out before installing the Polaris. • Do not handle the Polaris while it is operating. • Always remove the Polaris before swimmers enter the pool. • Disconnect the Polaris from the pool wall when cleaning or backwashing the pool filter. • After cleaning or backwashing, let the filtration system run for at least five minutes before re-connecting the Polaris. • Always remove the Polaris from the pool before chemical shock treatments. For customer service or su

• Для установки времени, нажмите кнопку “Time“ и установите текущее время кнопками “up/down“ , значение часа в диапазоне от 0 до 23, затемминуты – от 0 до 59. • Для установки времени работы обогревателя нажмите кнопку “Clocked” Выберите время работы обогревателя с помощью кнопок “up/down“ . Обогреватель будет автоматически поддерживать выставленную температуру. По истечению выставленного времени обогреватель автоматически выключится. На дисплее будет отображено текущее время. 6 . Для отмены уста

• After cleaning or backwashing, let the filtration system run for at least five minutes before re-connecting the Polaris. • New plumbing lines should be flushed out before installing the Polaris. • The Polaris should not be used to remove plaster dust in new pools. • Never handle the Polaris while it is operating. • When not in operation, always use the handle to pick up the cleaner. • Always remove the Polaris before swimmers enter the pool. • Always remove the Polaris from the pool before che

01 E EE2000 20002000Pol PolPola aar rri iis ssS SSal alales esesI IIn nnc. c.c.PARTS MANUAL PN 9915581 and MICROFICHE PN 9917173 11/00 TABLEOFCONTENTS VIRAGEW005197DandINT’LVIRAGEW005197I PartsManual BF BATTERYBOX ...................... B10 FUEL/WATERSEPARATOR ............. C10 BILGEPUMP ........................ B13 H C HULLandBODY ..................... A7-8 CARBURETOR ...................... C6 M COOLINGSYSTEM ................... B11 MAGNETO .......................... C8 CRANKCASE ..............

The Polaris climbs best in pools without sharp angles or curves in the transition from the pool floor to the pool wall. Approximately every three minutes the Polaris 380 goes into back-up mode. This action pulls the Polaris away from pool obstacles and increases its random pattern. Thrust Jet Adjustment The thrust jet powers the direction of the Polaris. Factory position is eleven o’clock, but depending on the pool, other settings are helpful. Sweep Hose Adjustment The sweep hose should move in

Technical tips . New product introductions . Event schedules . Parts and Service Manual information . Exciting details about The Way Out . Racing Information Check it out... All information in this manual is based on the latest product data and specifications available at the time of printing. Polaris Industries Inc. reserves the right to make product changes and improvements that may affect illustrations or explanations. No part of this manual shall be reproduced or used without the written per