or 1-800-668-1238 in CANADA IMPORTANT MANUAL DO NOT THROW AWAY INTRODUCTION THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator’s manual provides you with easy-tounderstand operating instructions. Read the whole manual and follow all the instructions to keep your new outdoor power tool in top operating condition. PRODUCT REFERENCES, ILLUSTRATIONSAND SPECIFI

Weight 75 lbs Warranty 2-year limited QTRBY-BUT BUILT FOR LIFE?

4. Make sure the vacuum bag strap is adjusted to allow a free flow of air from the vacuum bag elbow tube (Fig. 19). If the bag is kinked, the tool will not operate properly. WARNING: To avoid serious personal injury, do not wear loose fitting clothing or articles such as scarves, strings, chains, ties, etc., because they could get drawn into the air intake. Also make sure long hair does not get drawn into the air intake. Long hair must be pulled back and secured off shoulders and neck. Fig. 19 H

Consequently, it is not recommended that this tool be used for extended work on any fiberglass material, wallboard, spackling compounds, or plaster. During any use on these materials, it is extremely important that the tool is cleaned frequently by blowing with an air jet. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. 13 MAINTENANCE MAINTENANCE LUBRICATION All of the bearings

A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this operator's manual. ¦ DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center. ¦ DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol, or any medication. ¦ CUTTING INTO ELECTRICAL WIRING IN WALLS AND FLOORS CAN CAUSE THE BLADE AND METAL PARTS TO BECOME

When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used. **Ampere rating (on tool data plate) 0

. Do not smoke while handling fuel. • Mix and store fuel in a container approved for gasoline. • Mix fuel outdoors where there are no sparks or flames. • Loosen fuel cap slowly to release pressure and to keep fuel from escaping around the cap. • Tighten the fuel cap securely after refueling. • Wipe spilled fuel from the unit. Move 30 feet away from refueling site before starting engine. • Never attempt to burn off spilled fuel under any circumstances. • To reduce the risk of fire and burn injury

When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for your purchase. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS . Introduction......................................................................................................................................................................2 . Important Safety Instruc

When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product. SAVE THIS MANUAL FOR FUTURE REFERENCE 2 TABLE OF CONTENTS n Table of Contents 2 n Introduction 2 n General Safety Rules 3-4 n Specific Safety Rules 5 n Symbols 6-7 n Electrical 8 n Features 9 n Tools Needed 10 n Loose Parts 10 n Assembly 11-12 n Operation

It is important to keep moving the object back and forth across the grinding wheel and to cool the object frequently using the grinder’s Coolant Tray. AUTO-ON WORKLIGHT SHIELD RODS (RIGHT AND LEFT) SPARK DEFLECTOR (RIGHT) WHEEL GUARD WORK REST (RIGHT) ON SPARK DEFLECTOR (LEFT) OFF SAFETY SHIELD(S) WORK REST (LEFT) COOLANT TRAY SWITCH MODEL BGH825 Fig. 3c ASSEMBLY WARNING: Always disconnect the bench grinder from the power source before performing any assembly or adjustment. Failure to do so coul