Secure the guide rail in this position with the two screws [5-1] and tighten using the hexagon wrench. Lower the guide rail onto the support unit so that the groove in the underside of the guide rail fi ts on to the pin [4-5] of the support unit. The guide rail is properly attached when only a very slight lateral pressure is necessary for the pin to engage into the guide rail. The defl ector [6-1] is pushed onto the end of the guide rail. Close the rotary knob [6-2]. The defl ector prevents the

LED green – flashing: battery pack being charged. LED green – steady: battery pack fully charged, conservation charge on. LED red – flashing: general malfunction, e. g. full contact not being made, short-circuit, battery pack faulty. 5 LED red – steady: temperature of battery pack is outside permissible limit. It is essential that you read the instructions in the Chapter „Maintenance - Care“. Bit storage well You can insert several bits or bit extensions into the bit magazine (4.1) from the side

Depending on the pressure exerted on the button, the adjustment of running speed can be varied infinitely. Turn off by releasing the button. After releasing the button, the chuck is stopped and therefore, after-running of the equipment is prevented. To change the direction of rotation The selector button (1.4) determines the direction of rotation. -Turn button from right to left = clockwise rotation. -Turn button from left to right = anticlockwise rotation. -Selector button in central position =

567 669 The orbital sander was invented by Festool and the RS2E is the hidden champion of our line of sanders. The RS2E is a /2 sheet orbital sander with a fine, 2.5mm stroke and a real workhorse Unfortunately / sheet sanders have become more and more unpopular in recent years in the woodworking industry. They have been replaced by the widely used random orbital sander. Though random orbital sanders have a number of advantages, you can't beat / sheet sanders for smoothing out and finishing l

Be sureswitch is off before plugging in. Carryingtools with your finger on the switch or pluggingin tools that have the switch on invites accidents. 12Remove adjusting keys or switchesbefore turning the tool on. A wrench or keythat is left attached to a rotating part of the toolmay result in personal injury. 13Do not overreach. Stand on both feet ankeep proper footing and balance at alltimes. Proper footing and balance enables bettercontrol of the tool in unexpected situations. 14Use safety equi

of strokes 10 000 - 19 400 spm Abrasive stroke 2.5 mm (0.1 in.) Weight 1.5 kg (3.3 lbs.) Safety UL 745, CSA C22.2 No. 745 Symbols V Volts A Amperes Hz Hertz W Watt ~ Alternating current n0 No load speed Class II Construction rpm Revolutions per minute spm strokes per minute O Diameter Intended use The Deltex sander can be used to smooth wood, plastics, metal, steel, composite materials, paint- lacquers, filler, stopper and similar materials. Thanks to the triangular shape of the sanding pad the

Failure to do this may result in serious personal injury. Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back. Wear safety glasses during the entire adjustment process. Failure to comply may result in serious personal injury. Power Switch The Model G9984/G9985 must be turned ON to visually check the results of certain adjustments made to the sander; however, actual adjustments should never be performed while the machine is plugged in. Dust Collection The Model

Using too small of an extension cord can cause the cord to overheat. Extension Cord Ratings Cord Length Size (AWG) <25 Ft. 14 25-50 Ft. 12 50-100 Ft. 10 >100 Ft. Not recommended Personal Safety > Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. > Use personal protective equipm

484 455 (pack of 1) 2 are needed to connect 2 tables together PRODUCT DESCRIPTION The MFT table connector can be used to connect 2 or more Multi-Function Tables to get a larger work surface. These strong metal bars with 4 set screws slide into the "T" track spanning the tables to be joined as shown below. SUGGESTED USAGE For big jobs where a large surface with very versatile clamping options is needed. MFT's can also be joined together and be used with a long guide rail (e.g. FS 1900/2) to

Some examples of these chemicals are: • Lead from lead-based paints, • Crystalline silica from bricks and cement and other masonry products, • Arsenic and chromium from chemically-treated lumber. The risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals work in a well ventilated area and use approved safety equipment, such as dust masks that are USER MUST READ AND UNDERSTAND IN-specially designed to filter out micro- STRUCTI