United States LP/Propane Gas Sea Level and High Altitude Conversion Kit - P/N 903616 This kit is for LP/propane conversion in the United States at altitudes between zero and 10,000 ft. above sea level. Follow the installation instructions supplied with the kit for proper installation. Canadian LP/Propane Gas Sea Level and High Altitude Conversion Kit - P/N 903617 This kit is for LP/propane conversions in Canada at altitudes between zero and 4500 ft. above sea level. Follow the installation instr

These couplings can be ordered through your local furnace distributor. To install a coupling, slide the rubber coupling over the end of the pipe that is attached to the furnace and secure it with one of the hose clamps. Then slide the other end of the rubber coupling onto the other pipe from the vent and secure the coupling with the second hose clamp. Ensure that the connection is tight and leak free. NORDYNE condensing furnaces have been certified for installation with zero clearance between ve

Standards. Split System Heat Pump units are designed for use with a wide variety of fossil fuel furnaces, electric furnaces, air handlers, and evaporator coil combinations. These instructions are primarily intended to assist qualified individuals experienced in the proper installation of heating and/or air conditioning appliances. Some local codes require licensed installation/ service personnel for this type of equipment. Read all instructions carefully before starting the installation. USER’S

d. Cut out duct opening 1/4" larger than area marked. INSTALL FURNACE MOUNTING PLATE a. Place mounting plate (supplied within duct connector) at rear of the floor opening (See Figure 15). INSTALLING PLATINUM SERIES 14” ROUND DUCT CONNECTOR a. Place duct connector through the floor opening. (See Figure 15). b. Secure duct connector to floor. INSTALLING SCREW DOWN DUCT CONNECTOR a. Apply a bead of caulking, mastic, or other approved sealant around bottom side of 1/2” flange and restrictor plate, w

Airflow rates of 1800 CFM or more ** Factory Set Heating Speed 2. Temperature rises in the table are - Not Recommended 3. Temperature rises and airflows These conditions are not recommended. INSTALLATION REQUIREMENTS • NFPA-90B - Warm Air Heating and Air Conditioning Systems. Requirements and Codes This furnace must be installed in accordance with these instructions, all applicable local building codes, and the current revision of the National Fuel Gas Code (ANSI-Z223.1, NFPA-54). The current re

This screen is provided with the furnace installation instructions and functions to prevent debris from entering the combustion system. It should be installed on the combustion air intake collar or inlet PVC. If furnace location is such that this opening might be unintentionally obstructed, a 3" PVC elbow should be installed on the collar, and the screen placed inside the inlet of the elbow. See Figure 8. Installation In An Unconfined Space ! CAUTION: "Tight" buildings (with weather stripping an

e. Use only your hand to push in the gas control lever. Never use tools. If the lever will not push in by hand, don’t try to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion. f. Do not use this furnace if any part has been under water. Immediately call a qualified service technician to inspect the furnace and to replace any part of the gas valve or control system which has been under water. LIGHTING INSTRUCTIONS FOR STANDING PILOT MODELS

! ADVERTISSEMENT: RISQUE D’INCENDIE OU D’EXPLOSION Le non-respect des avertissements de securite pourrait entrainer des blessures graves, la mort ou des dommages materiels. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. – WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Leave the building immediately. • Immediately call your gas supp

These instructions are primarily intended to assist qualified individuals experienced in the proper installation of heating and/or air conditioning appliances. Some local codes require licensed installation/service personnel for this type equipment. All installations must be in accordance with these instructions and with all applicable national and local codes and standards. Installation Instructions Single Package Heat Pump IMPORTANT TABLE OF CONTENTS OWNER INFORMATION .........................

iMPORTANT: Read all instructions carefully before starting the installation. Specifications or designs are subject to change or discontinuance without notice and without incurring obligations. These instructions are primarily intended to assist qualified individuals experienced in the proper installation of heating and/or air conditioning appliances. Some local codes require licensed installation/service personnel for this type of equipment. WARNING: improper installation may damage equipment, c