Follow the gas supplier's instructions. If you cannot reach your gas supplier, call the fire department. ■ Installation and service must be performed by a qualified installer, service agency or the gas supplier. -ЛХ AVERTISSEMENT: Assurez-vous de bien suivre les instructions données dans cette notice pour réduire au minimum le risque d’incendie ou d’explosion ou pour éviter tout dommage matériel, toute blessure ou la mort. ■Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liqu
Mark the locations of the four mounting holes and the conduit entrance location on the wall. (The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.) 4. Fasten the backplate to the wall where previously marked. RECOMMENDATION: Wood wall - No. 16 (M8) wood screws, 2 3/4” (70mm) long Cement or brick - 1/4” (M6) stud expansion bolts, 3” (76mm) long Hollow wall - 1/4” (M6) toggle bolts, length depends on wall thickness 5. Run service wire to the dryer location and connect to t
+ Adjustable sound and speed New patent-pending technology allows the hand dryer to be adjusted to your preference - providing the perfect balance of speed, energy efficiency and sound. It’s ideal for sports stadiums, schools or a quiet library. + GXT MODEL REFERENCE CHART ABS White GXT9 GXT9-C Steel Chrome GXT9-M Steel White ADA Recessed Mounting Kit is available. See accessories chart. GXT9-SS Stainless Steel Universal Voltage 100-240 V 50/60 Hz Black Graphite GXT9-BG 12.5 A max. @ 120 V 6.5 A
Do not store or use gasoline or other flammable vapor and liquids in the vicinity of this or any other appliance. WHAT DO YOU DO IF YOU SMELL GAS * Do not try to light any appliance. * Do not touch any electrical switch; do not use any phone in your building. * Clear the room, building or area of all occupants. * Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions. * If you cannot reach your gas supplier, call the fire department. Installation and s
removal of cover: A) Loosen tamper-proof screws using wrench supplied, turn clockwise (donot remove). Located under bottom intake vent. B) To remove, place a hand on each side of cover and lift upward, then pull off. Dryers should be placed at least 2 feet (61cm) apart and at least 12” (30cm) 2. from washbasin. Do not install dryer over washbasin. Automatic dryers should be at least 18” (46cm) above any projection which may interfere with the operation of the automatic sensor. Hold the backplate
Options include a stainless steel cover with satin finish, a fixed nozzle and recessed mounting. PUSH BUTTON HAND DRYING PUSH BUTTON HAIR DRYING AUTOMATIC HAND DRYING ELECTRICAL RATINGS Drying Drying Drying Model Cycle Model Cycle Model Cycle Volts Amps Watts Hertz DR10N 40 sec DR10NH 80 sec DR10TN Automatic 110-120 15 1725 60 DR20N 30 sec DR20NH 80 sec DR20TN Automatic 110-120 20 2300 60 DR30N 30 sec DR30NH 80 sec DR30TN Automatic 208-240 10 2300 60 DR50N 30 sec DR50NH 80 sec DR50TN Automatic 2
42” (107cm) 40” (102cm) 30-40” (76-102cm) 34” (86cm) “DR-NH” Hair Dryer... 72” (183cm) 68” (173cm) 46-68” (117-173cm) 52” (132cm) Dimensions: WIDTH HEIGHT DEPTH NET WEIGHT Surface Mounted 11” 9-1/4” 6-5/8” 16 lbs. (7kg) Recessed Mounted 14-1/8” 14-1/8” 3-3/8” 23 lbs. (10kg) The dryer shall be manufactured by American Dryer to include a 16 gauge reinforced steel cover with a white enamel finish or 18 gage reinforced stainless steel cover with satin finish. Recessed units will include a 16 gauge s
Unit must be installed by a qualified licensed electrician. Do not connect any unit to a branch circuit over 20 amps. Dryers located in shower rooms or other wet locations should be equipped with ground fault interrupter(s). 6. Carefully replace the cover using tamper-proof bolts supplied. 1 1/4 1 (25 mm) (32 mm) 5/8 (17 mm) 9 1/2 (241 mm) DR Series Recess Mounted ROUGH OPENING 11 3/4” W (30cm) X 12 3/4” H 932cm) Operating Costs The only operating cost for the DR series hand dryer is electricity
Element is not accessible through nozzle and is protected by an automatic resetting circuit breaker (thermostat). It produces an air temperature of 130-145.F at a 72.F ambient room temperature. FEATURES/MATERIALS: • Cover One piece industrial drawn 16 gauge reinforced steel or 18 gage reinforced type 304 stainless steel satin finish. • Finish Electrostatically applied white enamel or stainless steel satin finish. Resistant to chipping and cleaning agents. • Tamper-Resistant One tamper-resistant