©2004, 2005 Stewart Filmscreen Corporation Stewart Filmscreen reserves the right to make changes to the product specified in this document. From time to time, this document is updated. Current versions of documentation are posted on the Stewart Filmscreen website at AVS—Automatic Vertical Screen OWNER’S MANUAL Contents Tothe Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Preparing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Inst

• Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • Features: • Fits 23" to 84" flat panel screens • Easily expandable adapter brackets and wall plate • Adjustable tilt of +15°/-5° for viewing flexibility • Intuitive design for easy installation • Security hardware for theft resistance and safety Max UL Load Capacity 250lb (113.5kg) Installation and Assembly: OneMount™ This product is UL Listed. It must be installed by a qualified professional installer. Note: Re

The top mounting hole should be 2.5" above the desired screen center as shown in figure 4.1 on page 8. Drill four 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (EE) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (DD). Level, then tighten all fasteners. NOTE: Six holes and six sets of fasteners are required when mounting the wall plate for equipment weighing greater than 200 lbs. • When installing Peerless wal

CENTER BRACKETS VERTICALLY ON BACK OF SCREEN X CC X Note: "X" dimensions should be equal. KNOBS FACE OUT BB fig 2.1 NOTES: • Always use multi-washers when attaching tilt brackets (BB and CC) to your screen when using small, medium or large screws. No multi-washer is required for extra large (M8) screws. • Use the corresponding hole in the multi-washer that matches your screw size as shown in fig 2.2. MULTI-WASHER fig 2.2 MEDIUM HOLE FOR M5 SCREWS LARGE HOLE FOR M6 SCREWS SMALL HOLE FOR M4 SCREWS

The open sides of the cross chain hooks must be facing away from the tire when the chain is installed. Make sure all twists are out of the chain assembly. A this side Position the side chain with the fingertip hook to go on the inside of the tire (toward body of the machine/vehicle). As a result, the side chain with the outside fastener will then be positioned to go on the outside of the tire. 2 Grasping the middle of the inside fastener side chain, lift and drape the chain assembly over the

• Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • NOTE: Read entire instruction sheet before you start installation and assembly. NOTE: Read entire instruction sheet before you start installation and assembly. • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer ca

WARNING 1 3 2 B Drill holes and insert anchors (B). Place plate (A) over anchors (B) and secure with screws (H). Tighten all fasteners. A H B concrete surface 6 of 20 ISSUED: 02-05-09 SHEET #: 202-9312-1 M L N K N E G N Attaching Adapter Plate to Screen with VESA® 200 x 100 or 200 x 200 Mounting Pattern Attach hook bracket (M) to adapter plate (N) using four M5 x 6 mm screws (K) and #10 washers (L) as shown. 2 FOR VESA® 200 x 100 MOUNTING PATTERN: Choose hole pattern as shown below. Attach adapt

Before you begin, make sure all parts shown are included with your product. PWV240/BK PP740 Description Qty. Part # A wall mount assembly 1 095-0545-GB B concrete anchor 2 590-0320 C retaining spacer 4 590-5005 D 1/4-20 x 13 mm flat head phillips screw 2 520-1209 E M4 x 10 mm phillips screw 4 504-9012 F M4 x 20 mm phillips screw 4 504-9020 G M6 x 12 mm phillips screw 4 520-1128 H #14 x 63.5 mm flat head wood screw 2 520-1202 I M6 x 20 mm phillips screw 4 520-9402 J M6 x 30 mm phillips screw 4 51

A R C H I T E C T S S P E C I F I C A T I O N S The PRS Series Clamp-Style Universal Projector Mount shall be a Peerless model and shall be located where indicated on the plans. It shall feature 25°(+5°/-20°) pitch, 20°(+10°) roll, 360° yaw (when attached to an extension column), and +/-15° yaw (when flush mounted). It shall have a 25 lb load capacity. It shall have a quick release spring loaded screw for easy removal and installation of the projector. It shall be constructed of aluminum alloy f

TECHNICAL DATA SHEET - PRS Series Clamp-Style Universal Projector Mount Accessories: • Ceiling Plates (various models available) • Cord Wrap (ACC 852, 852S, 852W) • Fixed and Adjustable length Extension Columns, 1 1/2" NPT (“EXT” or “ADJ” models) • Fixed length Extension Columns, 3/4" NPT (“FLP” models) • Armor Lock Plus™ security cable with Lock (ACC 020) • Armor Lock Plus security cable (ACC 021) • Side to Side Adjuster (ACC 830) Dimensions: For product dimensions, see page 2. PRS SERIES PROJ