If running heater with damper open, non-combustible material above fireplace opening is not needed. Go to Installing Damper Clamp Accessory for Vented Operation, page 9. Minimum Non Combustible Material Clearances If Not Using Mantel Note: If using a mantel, go to column 3. If not using a mantel, follow the information on this page. You must have non combustible material(s) above the fireplace opening. Non combustible materials (such as slate, marble, tile, etc.) must be at least 1/2 inch th

After 30 seconds, release control knob. Now follow step 8, page 14. INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT FLAME PATTERN Figure 24 shows a correct pilot flame pattern. Figure 25 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. This will cause the thermocouple to cool. When the thermocouple cools, the heater will shut down. Thermocouple Pilot Burner Figure 24 - Correct Pilot Flame Pattern Therm

inches Area of Various Standard Round Flues Diameter (ins.) Area (sq. ins.) 5” 20 sq. inches 6” 29 sq. inches 7" 39 sq. inches 8" 51 sq. inches INSTALLING HEATER BASE ASSEMBLY A WARNING: You must secure this heater to fireplace floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak. A WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. This will insure a

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer ® Patent Pending FLAME-MAX® Golden Oak Log Design 18", 24", 30", and 36" Variable Manually-Controlled and 18", 24", and 30" Thermostatically- Controlled Models 18", 24", and 30" Variable Manually-Controlled Model FLAME-MAX® Birch Log Design ® Save this manual for future reference. WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal i

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS • Do not try to light any

Propane/LP Supply Tank External Regulator tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from fireplace (see Figure 40). WARNING: A qualified ser- vice person must connect fire- place to gas supply. Follow all local codes. CAUTION: Use pipe joint seal- ant that is resistant to liquid pe- troleum (LP) gas. Propane/LP Supply Tank External Regulator tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from fireplace (see Figure 40). OW

CAUTION: Do not operate this fireplace with a broken glass door panel. Do not operate this fireplace without the glass door panel securely in place. For replacement part information see Replacement Parts, page 35. Figure 47 - Removing/Replacing Glass Door Glass Door Assembly Screw Lower Bracket for Glass Door Assembly 1. Remove the upper louver panel by lifting upward and out (see Figure 46). 2. Remove the screws from the three tabs at the top of the glass door while holding door securely keepin

3. Insert other rod into front hole on right side of firebox and fasten using remaining shoulder screw. Rear Hole Figure 16 - Installing Fireplace Screen (Shown Without Fireplace Hood for Clarity) ...............................................................................................................................................................................................................................................................................................................

Route power cord through both plastic bushings and plug the power cord into a 3prong grounded wall receptacle near the firebox. b. If your firebox installation is recessed and/or pre-wired, see Built- In Installation of Blower Accessory, column 2. 8. Turn on power to duplex outlet if previously turned off per the warning in step 1. 9. Check to make sure that the power cord is completely clear of the blower wheel and that there are no other foreign objects in blower wheel. Turn blower on and chec