Important Notice: Damages resulting from the disregard of safety and general user instructions found in this user manual are not subject to any warranty claims. ©Elation Professional® 6 impression™ ©Elation Professional® 7 impression™ 3. FIXTURE OVERVIEW 1. Head and Lens Assembly (actively and passively cooled) 2. Arm with various cooling vents 3. LCD-Full Text Display and Menu with Foil Key Pad (data entry) 4. Base with various connectors and Camlock mounting system 5. Power On/Off Switch 6. DM

Please note that the outside temperature should not exceed 45° C. 8.4 Personality: 8.4.1 Status setting Address via DMX -This function allows the DMX address to remotely be adjusted from a DMX console. This setting requires special settings for both the controller and ©Elation Professional, Los Angeles Ca. 27 Design Spot 300 Pro™ the fixture. RDMX is on by default. For operational instructions please see Section 9/Page 33 of this manual “Remote DMX addressing.” No DMX Status – This function dict

23 DESIGN LED 36 Pro™ Channel 6 -General dimming / Program Speed Control This channel has two functions depending on the operating mode. When running the built-in programs this channel will control the program speed, when not running the built-in programs this channel will control master dimming. 0-255 Dimming (0%-100%) ~ Normal Operation 0-255 Speed (min to max) ~ When running built-in programs on channel 4 ©Elation Professional, Los Angeles Ca. 24 DESIGN LED 36 Pro™ ©Elation Professional, Los

The illustration below details the functionality of the LED indicators. .... Lamp on Lamp on DMX OK DMX OKNO DMX NO DMX Lamp off Lamp off The first LED indicators represents DMX signal: • If the indicators is on a clean DMX signal is present • If the indicator is off there is no DMX signal present The second LED indicator represents lamp condition; this is only applicable to fixtures with traditional lamp sources. ©Elation Professional, Los Angeles Ca. 17 DESIGN LED 36 Pro™ ©Elation Professional

All electrical connections must performed by qualified personal. Be sure the available voltage matches the voltage requirements of the unit. Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. Always disconnect from main power before performing any type of service or any cleaning procedure. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. Please be

- The DMX controller is switched off or defective. - The DMX cable or connector is defective. - A DMX terminator has been inserted into the last fixture in your DMX chain. DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 18 8. FIXTURE MENU On-Board System Menu: The Design LED 36 Pro™ comes with an easy to navigate system menu. This next section will detail the functions of each command in the system menu. LED Control Panel: The control panel located on the base of the fixture allows you

Step 3 – Playing a Program To initiate a program follow the procedure below: • Access the main menu and use the “Up” and “Down” to toggle to “Function Mode” and tap the “Enter” button. • In the next screen select “Auto Program” and tap the “Enter” button. • There are now two selections, “Master” and “Alone.” Select “Master” when running multiple fixtures in a master/slave configuration. See section 11.2 “Master/ Slave Operation” on page 37 for proper set-up instructions. Select “Alone” when runn

General Information……………………………………………………………………… 3 a. Introduction………………………………………………………………………. 3 b. Unpacking………………………………………………………..…………..… 3 c. Customer Support…………………………………………….………………… 3 d. Warranty Registration……………………………………………………..…… 4 e. Discharge Lamp Warning……………………………………………………… 4 2. Safety Instructions………………………………………………………........…………. 7 3. Features…………………………………………………………………………………… 9 4. General Guidelines………………………………………………………………………. 10 5. Lamp Installation…………………………………………………………………………. 11 a.

Improper optimization may add a yellow tint to the lamp output and reduce intensity. The minimum deviation amount is 1.0mm. Running the fixture within a lower deviation can cause damage to the lamp and/or lens. The Design Beam 300™ lamp holder is aligned at the factory. However, due to slight imperfections in all lamps, fine adjustments will improve light performance. Please follow the procedure below for proper lamp optimization: 1. Using a DMX controller or the control panel on the unit, strik

via DMX Auto run if no DMX Pan Reverse movement Tilt Reverse movement Fine resolution switch Pan Degree Select Movement Feedback switch Movement Mode Select Sensitivity of Mic. Service Setting Service Password Fan Voltage Password=XXX High/Low Service Code“=050” Fan Voltage Select Fans Control Auto Fans Speed High Fans Speed Low Fans Speed Fans Speed Mode Select Display Setting Shutoff Time Display shutoff time Temperature C/F Celsius Fahrenheit Temperature switch between C°/F° Initial Effect PA