It may be fully opened when rapid heating is required or to help clean any deposits from the glass. It will not be possible to keep the glass clean if this control is fully closed, particularly immediately after refuelling. RIDDLING When burning solid fuels riddling twicea day is usually sufficient. When burning wood or peat, ash should be allowed to build up and generally weekly riddling will be sufficient. The fire should be riddled with the doors shut (see Fig 2.) Place the tool onto the ridd

uk w w w . c h a r n w o o d . c o m OPERATING INSTRUCTIONS FOR THE CHARNWOOD COUNTRY 15B Before lighting the stove check with the installer that the work and checks described in the Installation Instructions have been carried out correctly and that the chimney has been swept, is sound and free from any obstructions. Do not light the fire before the boiler and heating system have been filled with water as this can damage the boiler. FUELS Please pay careful attention to the special points made w

The following points should be noted and with a little care should enable the glass to be kept clean in most situations: a) The airwash relies on a supply of heated air to keep the glass clean, therefore, when lighting the stove allow the firebed to become well established before closing the airslides. This may also be necessary when re-fuelling the stove. b) When re-fuelling keep the fuel as far back from the front firebars as possible, do not try to fit too much fuel into the firebox. c) Never

The fire should be riddled with the doors shut (see Fig 2.) Place the tool onto the riddler rod and rotate between the ‘3 o’clock’ and ‘5 o’clock positions several times. Too much riddling can result in emptying unburnt fuel into the ashpan and should therefore be avoided. Clinker should regularly be removed from the firebed. After riddling, the grate should be put back into the solid fuel or wood position as required (the tool should be horizontal for solid fuel or vertical for wood). REFUELLIN

The end of the flue pipe must line up Page 8 LA30iB 3.99 Central Heating Flow Central Heating Return Drain Cock at Lowest Point Drain Cock Indirect Hot Water Cylinder Cold Water Tank Overflow Feed and Expansion Tank 22mm Open Vents Gravity Radiator Circulating Pump Central Heating Return Drain Cock at Lowest Point Drain Cock Indirect Hot Water Cylinder Domestic Hot Water Draw Off Cold Water Tank Overflow Overflow Feed and Expansion Tank 22mm Open Vents Gravity Radiator Circulating Pump Injector

This stove must not be used with any solid fuel, it is only suitable for natural gas or liquefied petroleum gas (LPG) according to the burner unit supplied. Ensure that the local gas distribution conditions, the nature of the gas pressure and the adjustment of the stove are compatible. Check that the burner data plate corresponds with the type of gas which is to be used i.e. natural gas or LPG. The burner unit data plate is attached by a chain to the underside of the burner unit. The site of the

Fume Emission Warning Note: Properly installed and operated this appliance will not emit fumes. Occasional fume from deashing and re-fueling may occur. Persistent fume emission is potentially dangerous and must not be tolerated. If fume emission does persist then take the following immediate actions should be taken: a) Open the doors and windows to ventilate the room. b) Let the fire out and safely dispose of fuel from the appliance. c) Check for flue or chimney blockage, and clean if required.

The outputs were obtained burning smokeless fuel over a four hourly re-fuelling cycle. CHIMNEY In order for the appliance to perform satisfactorily the chimney height must not be less than 4 metres measured vertically from the outlet of the stove to the top of the chimney. The chimney should preferably be 175 mm (7 inches) or 200mm (8 inches) internal diameter or square with sides of 175mm or 200mm internally and must not be less than 150 mm (6 inches) internal diameter or 150 x 150mm internal s

Some deposits on the glass may be burnt off simply by running the fire at a fast rate for a few minutes. Do not use Tool Pull Forward and Swing Down Tool Throat Plate Throat Plate Pull Forward and Swing Down Country 8 Country 12 Fig. 3. Throat Plate Location abrasive cleaners or pads as these can scratch the surface which will weaken the glass and cause premature failure. Aerosol spray cleaners should not be used near the appliance whilst it is under fire. When not in use If the fire is going to

FUELS Wood Wood must be dry and well seasoned. Ideally it should be cut, split and stacked under cover for at least a year and preferably two years before being burnt. Hard woods, such as Ash, Beech and Oak are preferable to Soft woods such as Pine. The wood should be burnt in a bed of ash on the flat base of the stove. Burning wet unseasoned wood will result in heavy tar deposits in the chimney and reduced outputs. Peat Cut peat should be dried before burning to reduce tar deposits. Peat should