A study by the Federal Emergency Management Agency (an agency of the United States government) indicated that smoke detectors may not go off in as many as 35% of all fires. While fire alarm systems are designed to provide early warning against fire, they do not guarantee warning or protection against fire. A fire alarm system may not provide timely or adequate warning, or simply may not function, for a variety of reasons: Smoke detectors may not sense fire where smoke cannot reach the detectors

All remaining points above 568 will report as fire alarm points. Document 50934 Rev B 5/15/00 PN 50934:B To access Type Mode, press the MODE key followed by the 4-digit code 8973 and then press the [ENTER/STORE] key. The ADT-UDACT will display three digits. For example, initial entry will display 01 0. To access Type Mode, press the MODE key followed by the 4-digit code 8973 and then press the [ENTER/STORE] key. The ADT-UDACT will display three digits. For example, initial entry will display 01

Use this command to silence your Command Center sounder during service alert, and to reset the Command Center alarm memory. COMMAND To use COMMAND 4: 1. Ensure that your security system is disarmed. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the [_4j key. The Command Center sounder is silenced, and any flashing Zone Status indicator lights are turned off if the zone is normal. 13 Transmit Test Report O I have this feature. □ I do not have this feature

Most fire related deaths occur at night when the occupants suffocate in their sleep from smoke and deadly gases, rather than from bums. To help reduce this risk, the following three-step program should be implemented: 1. Minimize fire hazards around the home. Smoking in bed, cleaning with flammable liquids such as gasoline, leaving children home alone, and unsafe Holiday decorations are some of the more common causes of household fire. 2. Install a fire warning system. The primary purpose of t

Now classified in accordance with ANSI/SIA CP-01-2000 (SIA-FAR) User’s Guide ® TM Power864 SECURITY SYSTEM Quick Reference Guide The following chart lists the basic functions of your system alphabetically, and the keys to press for each function. Refer to the listed page number for more information. NOTE: Some functions may not be available on your system. Ask your installer for more information. To do this: Press this: See page: Arm system (Away): ................................[access code],

WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. l Table of Contents System Keypads . . . . .. .. .. .. .. . . . . . . . . . . . .. .. .. .. .. 1 KeypadDisplay Symbols . .. .. .. .. .. . . . . . . . . . . . .. .. .. .. .. 2 Reference Sheets 3 Access Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System I

3 ARMING ....................................................................................... 3 Arming The System Prior To Leaving ..................................... 3 Arming The System Without Leaving ..................................... 3 System Not Arm (Ready Light Off) .................................. 4 DISARMING ...................................................................................... 5 Disarming Upon Entering The Premises ................................ 5 ALARM CONDI

FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not install

Ensure that no zones are unintentionally 4 bypassed when arming your system. Zones cannot be bypassed once the system is armed. Bypassed zones are automatically cancelled each time the system is disarmed and must be bypassed again, if required, before the next arming. Bypassing Zones With the system disarmed. 1. Press to enter the function menu. The keypad will display “Press 4 for < > Zone Bypass”. 2. Press or , then your [access code] (if required). The keypad will display “Scroll to < > Bypas

This will turn off all C304 modules and Notification Appliance Circuits, temporarily turns off resettable power to 4-wire detectors, causes a 'System All Normal' message to be displayed on the ADT-LCD40 and sends a 'System Reset' message to the FACP display, printer and Unimode 200 history files. It also turns on all system LEDs, piezo sounders and LCD display segments as long as the Reset switch is held (lamp test). Any alarm or trouble that exists after a Reset will resound the system. Documen