Bits 7, 6, 5, 3, 2, 1, and 0 are changeable, because those bits are all ones. Bit 4 is not changeable. Though the drive always reports non-zero values in bytes 00 and 01, those particular bytes are never changeable. The Changeable values list can only be changed by downloading new firmware into the flash EPROM. On standard OEM drives the Saved values are taken from the default values list and stored into the saved values storage location on the media prior to shipping. When a drive is powered up

Cheetah 10K.7 SCSI Product Manual, Rev. D Table 15: LW 68-conductor LVD P cable signal/pin assignments [11] Note. Note: A minus sign preceding a signal name indicates that signal is active low. Signal name [1] Connector contact number [3] Cable conductor number [2] Connector contact number [3] Signal name [1] +DB12 1 1 2 35 –DB12 +DB13 2 3 4 36 –DB13 +DB14 3 5 6 37 –DB14 +DB15 4 7 8 38 –DB15 +DBP1 9 39 –DBP1 +DB0 6 11 12 40 –DB0 +DB1 7 13 14 41 –DB1 +DB2 8 15 16 42 –DB2 +DB3 9 17 18 43 –DB3 +DB4

The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data. The following conditions are considered DST failure conditions: • Seek error after retries are exhausted • Track-follow error after retries are exhausted • Read error after retrie

Wenn Sie das Systemgehause nicht an die HDA/PCB- Erdung anschlie.en wollen, mussen Sie das Laufwerk auf nichtleitende Weise (galvanisch isoliert) im Host-Sys Barracuda 4LP Installation Guide, Rev. B tem einbauen. Die daraus u.U. resultierende verstarkte elektromagnetische Strahlung fallt in den Zustandigkeitsbereich des Systemdesigners. 5. Replace the host system’s cover. 5. Setzen Sie das Gehauseoberteil des Host-Systems wieder auf. Barracuda 4LP Installation Guide, Rev. B [4] A F D E L [1] [3]

Barracuda 4LP Installation Guide, Rev. B Technical support services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional assistance with your Seagate® drive or other Seagate products, use one of the Seagate technical support services listed below. SeaFONE® at 1-800-SEAGATE (1-800-732-4283) Seagate’s 800 number allows toll-free access

29 N drives section ......................................................................... 36 W/WD drives section .................................................................40 WC/DC drives section................................................................45 ©1997 Seagate Technology, Inc. All rights reserved Publication Number: 77767492, Rev. B January 1997 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology, Inc. Barracuda, SeaFAX, SeaF

The top example in Figure 2 shows an internal hard disc at one end of the SCSI bus with the SCSI controller at the other end (both are terminated). The bottom example shows two additional SCSI devices connected externally—this means the SCSI controller is no longer on the end of the SCSI chain and should not be terminated. Note. Some controllers prefer to remain terminated even if they are in the middle of the chain. Also, some controllers treat the internal and external chains as separate logic

Other customers should contact their place of purchase. Seagate offers comprehensive customer support for all Seagate drives. These services are available worldwide. Location Phone number FAX number Asia Pacific and Australia 65-485-3595 65-488-7503 Europe, Middle East, and Africa 31-2031-67300 31-2065-34320 Japan 81-3-5462-2904 81-3-5462-2979 USA 1-800-468-3472 405-949-6740 Other Americas (Brazil, Canada, Mexico) 405-949-6706 405-949-6738 Cheetah 18 Installation Guide, Rev. A Location Phone num

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist 1080sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCSI Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents Introduction .. .. .. .. .. .. .. .. .. .. .. .. . 1

2. Does the computer recognize the drive? Verify that the drive is enabled in the system CMOS or setup program. If not, select the autodetect option and enable it. If your drive has a problem, it may not be recognized by the system. 3. Does FDISK detect the drive? Run the FDISK program located on your Windows startup diskette. Type fdisk/status to verify that your hard drive is present and recognized by the system. 4. Does Scandisk find the drive defect-free? Scandisk is a utility located on you