Log:
Trier : Nom ↑   Téléchargements   Évaluation   Taille ↑  

Allstar Products Group CHALLENGER AC9500

Téléchargements : 38 Taille : 1 mb    Fabricant : Allstar Products Group  
Catégorie : Portail automatique

Manually raise the door to its high arc position and temporarily clamp in that position. With the door in this high arc position, measure the distance from the top of the door to the floor (see figure at left). Subtract the actual door height from the high arc distance to the floor. This is the high arc rise of the door. Unclamp and close the door. Using the table below, draw a horizontal line at the appropriate height above the door to intersect with the vertical centerline. 110049 1/2” Above H

Allstar Products Group 6000

Téléchargements : 13 Taille : 1 mb    Fabricant : Allstar Products Group  
Catégorie : Portail automatique

2 Product Features ................................................................................... 2 Component Identification/Tools Required ........................................... 4 Section A: Assembly Instructions ....................................................... 5 Section B: Installation Notes ................................................................ 6 Section C: Installing the Operator ....................................................... 7 Identify Your Door Type ....

Allstar Products Group 8832

Téléchargements : 7 Taille : 169 kb    Fabricant : Allstar Products Group  
Catégorie : Portail automatique

Models 9931, 8832, 8833: The coding switch in these models consist of eight or nine small switches, each of which can be placed in any of three different positions. (+, 0, -). See Fig. 2. Using a small screwdriver, set both the transmitter and receiver coding switchesidentically. (Your private code setting). DO NOT SET ALL THE SWITCHES IN THE SAME POSITION. EXAMPLE: FIGURE 2 NOT ALL + or 0 or - IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS

Allstar Products Group 9921

Téléchargements : 7 Taille : 169 kb    Fabricant : Allstar Products Group  
Catégorie : Portail automatique

After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 35 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. B. If the transmitter doesn’t activate the operator, check the coding switches on both the transmitter and receiver to assure an “exact” match. ( See Fig. 2 & 3) . This may necessitate a reprogramming of a Quik Code Classic transmitter to match the receiver coding swi

Allstar Products Group 9921T

Téléchargements : 7 Taille : 468 kb    Fabricant : Allstar Products Group  
Catégorie : récepteurs radio

8 switches w/ + 0 - WARNING Disconnect power to operator before any installation or repair. Follow all instructions provided by the manufacturer of your operator. After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 45 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. However, environmental conditions and the location of the transmitter and receiver will affect distance.

Allstar Products Group 8822

Téléchargements : 6 Taille : 169 kb    Fabricant : Allstar Products Group  
Catégorie : Portail automatique

A. Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter. (See Fig. 1A). B. Use a small screwdriver or knife to remove small door on back of receiver to gain access to coding switches. (See Fig. 1B) IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION. Note: If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx Allstar Rece

Allstar Products Group CHALLENGER ACJ9500

Téléchargements : 5 Taille : 1 mb    Fabricant : Allstar Products Group  
Catégorie : Portail automatique

To assemble, screw the door arm rod into the the door arm tube in a clockwise direction approximately ten turns. Connect the door arm assembly into the trolley with the open end of the rod Trolley (Close Limit Position) hook facing the power head unit (away from the door). Extend the manual release cord (connected to the trolley) and thread through the warning tag and red pull knob handle. Adjust so the knob is 6 feet above the floor and secure Cushion Arm with a double overhand knot in the end

Allstar Products Group 8832T

Téléchargements : 5 Taille : 468 kb    Fabricant : Allstar Products Group  
Catégorie : récepteurs radio

Write the code that you matched from your transmitter or receiver in the grids below. 1 2 3 4 5 6 7 8 9 + / On BUTTON Zero BUTTON - / Off BUTTON - PUT THE TRANSMITTER IN PROGRAM MODE 1. First, press and hold the + 1a. First, press and hold the - button. The Red LED will turn on. Next, button. The Red LED will turn on. Next, while continuing to hold the + button, while continuing to hold the - button, press and hold the - button. Continue press and hold the + button. Continue to hold both buttons

Allstar Products Group LT 50

Téléchargements : 5 Taille : 979 kb    Fabricant : Allstar Products Group  
Catégorie : Portail automatique

Disconnect the power from the opener before removing cover and cutting the jumper. MAKE SURE YOU DISCONNECT THE POWER BEFORE CUTTING THE JUMPER. THE RUN TIMER WILL NOT CHANGE IF THE JUMPER IS CUT WITH THE POWER CONNECTED. This jumper is located under operator cover on the control board, as illustrated. 110057-2 Cut and Separate IMPORTANT SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ AND FOLLOW ALL INSTRUCTIONS! • Ensure authorized personnel only operate the door.

Allstar Products Group 8833 OCS

Téléchargements : 4 Taille : 217 kb    Fabricant : Allstar Products Group  
Catégorie : récepteurs radio

Some models are designed to operate multiple receivers. A selector switch on the Transmitter determines which door will be controlled in a multi-door installation. The Receiver is connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. • ALLSTAR TRANSMITTERS ARE INTENDED FOR USE WITH COMMERCIAL DOOR OPERATORS ONLY. DO NOT USE FOR ANY OTHER PURPOSE. DO NOT MODIFY IN ANY MANNER. • CHECK LOCAL BUILDING AND ELECTRIC





catégories