• The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain se

• The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain se

If the RCA inputs are not grounded adequately via the signal source, electrical noise from the vehicle may be picked up in the system. © 2003 Directed Electronics, Inc FRONT PANEL CONNECTIONS/CONTROLS 200/2 - 300/2 1. H HHi iig ggh hh L LLe eev vve eel ll I IIn nnp ppu uut tt C CCo oon nnn nne eec cct tto oor rr - Accepts board active crossover. FLAT does 1v to 10v input from the headunit’s not attenuate any frequencies and speaker output. is for full-range speaker systems. HPF attenuates low fr

AmplifierMODELXTR2502XTR5002OWNER'S MANUAL AmplifierMODELXTR2502XTR5002OWNER'S MANUAL Contents english 1 Francais 19 espanol 35 Deutsch 51 Italiano 67 Portugues 83 Introduction 2 What’s in the Box 2 Practice safe sound™ 2 end Panel Layouts 3 CeA specifications 4 specifications 5 Amplifier settings 6 signal Input and output Configurations 6 Input Gain 6 Line output Configurations 6 Internal Crossover Configurations, Flat (full range) 6 Crossover switch 6 Low-Pass Crossover 6 High-Pass Crossover 7

3. Check for any hazards or obstructions such as gas tanks, fuel or brake lines, and wiring harnesses before mounting the amplifier. They may also impair a driver’s ability to hear traffic sounds or emergency vehicles. Use common sense and practice safe listening habits when listening to or adjusting your audio system. 4. Pick a mounting location that will provide adequate access and ventilation and protect the amplifier from heat, moisture, and dirt. 5. Avoid sharp metal areas when routing cabl

(70 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR2504 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum power capability of 250 Watts into two 4. bridged loads l XTR5004 -80 Watts at 4. (125 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR5004 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum

3. S SSi iig ggn nna aal ll C CCo oon nnn nne eec cct tti iio oon nn - Connect an RCA cable between the BRIDGE OUT jack of the 1100d5 and the SLAVE IN jack of the slaved 600d as shown in Figure 6. 4. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh - Set the slave/master switch of the 600d to the slave position. This will put the I/O RCA jack in the SLAVE IN mode so it will accept the audio signal from the 1100d5’s sync out RCA jack. N NNO OOT TTE EE: ::There is only one

Directed has been the leader in high-quality and innovative security products in the U.S. since 1990. Now we introduce to the car audio industry the same winning formula - products that meet the stringent standards of today’s mobile electronics enthusiast yet priced for anyone’s budget. Featuring high-efficiency MOSFET power supplies, flexible on-board crossovers, and state-of-the-art audio design, Directed Audio amplifiers will satisfy every music lover’s needs for years to come. Your Directed

The chassis connection point should be scraped free of paint and dirt. Use only quality crimped and/or soldered connectors at both ends of this wire. DO NOT connect this terminal directly to the vehicle battery ground terminal or any other factory ground points. REAR PANEL CONNECTIONS 8 © 2003 Directed Electronics, Inc FIGURE 2—AMPLIFIER CONNECTIONS 250/4 FRONT HIGH INPUT +- L R 1 FRONT HIGH INPUT + - REAR 1 OUTPUT INPUT R L 2 3 L R 7 INPUT 6 3 BASS EQ. OFF ON 5 LPF HPF FLAT MIN MAX 4 GAIN 5 LPF

Electronics, the industry leader in high Directed Audio power amplifiers come quality automotive security and audio with a two-year limited warranty if equipment since 1990. installed by an authorized Directed Directed Audio power amplifiers dealer. If not installed by an authorized continue to set new standards of perfor-dealer, Directed Audio power amplifiers mance, reliability, and affordability in are covered by a one-year, parts-andthe mobile electronics industry. labor limited warranty. Fe