You may use petroleum-based lubricant that is premium quality, does not contain detergents, contains only anti-rust, anti-oxidation, and anti-foam agents as additives, has a flashpoint of 440°F (227°C) or higher, and has a auto-ignition point of 650°F (343°C) or higher. See the petroleum lubricant viscosity table below. The table is intended as a general guide only. Heavy duty operating conditions require heavier viscosities. Refer specific operating conditions to NorthStar Product Support at 1-

Use Non-detergent pump oil (item # 35605). Maximum RPM 45929: 1570 RPM (700 RPM Minimum) 45930: 1450 RPM (700 RPM Minimum) Minimum Horsepower 45929: 5.0 hp gas engine, 3.0 hp electric motor 45930: 5.5 hp gas engine, 4.0 hp electric motor Displacement 45929: 11.3 CFM 45930: 16.9 CFM CFM @ 90 psi 45929: 8.2 45930: 13.2 Rotation Pump crankshaft MUST rotate in direction of arrow cast into flywheel. Drive Belt Flywheel requires “A” style belt Air Flow Belt guard MUST allow maximum air flow past pump.

A moment of inattention while operating pneumatic tools may result in serious personal injury. 2. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 3. Avoid accidental starting. Be sure the trigger is off before connecting to the air supply. Carrying pneumatic tools with your finger on the trigger, or connecting pneumatic tools to the air supply with the trigger o

Use common sense. . Always be sure to stand inside the Operator Zone when running your log splitter. IMPORTANT: Before starting the splitting operation, cycle pressure plate of the splitter three to four times back and forth by pushing and releasing switches to help remove any air that may have mixed into the hydraulic fluid during handling, storage, etc. Oil is incompressible; therefore, to ensure the efficiency of the log splitter, it is important that the hydraulic system does not contain air

Service or maintenance performed by unqualified personnel could result in a risk of injury. 24. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Hoist. These carry important information. If unreadable or missing, co

The plug and outlet should look like those in the following illustration. (See Figure A.) PAGE 7 DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either

28. Compressed air from the unit may contain carbon monoxide. Air produced is not suitable for breathing purposes. 29. Always use a respirator when spraying paint or chemicals. 30. The air pressure switch is set at the factory for optimum performance of your equipment. Never attempt to bypass or remove this switch as serious damage to equipment or personal injury could result from excessive air pressure. 2 KNOW YOUR COMPRESSOR Handle Air Filter Air Chuck Regulator Pressure Gauges Figure 1. Air C

• Avoid accidental starting. Ensure the switch is in the off position before plugging tool into power outlet. Do not carry the power tool with your finger on the switch. • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. • Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. 2 TOOL USE AND CARE • Do not

1 SAFETY RULES 1. Know your machine. Read this manual carefully. Learn the machine’s applications and limitations, as well as specific potential hazards peculiar to it. 2. Ground all machines. If the machine is equipped with three-pin plug, it should be plugged into a three-pin electrical socket. Never remove the ground pin. 3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 4. D

Before using this product, please read the following instructions carefully. Technical Specifications Item Description Item Description Square Drive 1/2" Air Inlet Diameter 1/4"- 18NPT Free Speed 145 RPM Min. Hose Size 3/8" Max. Torque 65 ft-lbs Max. air pressure 90 PSI Air Consumption 4.5 CFM SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep this manual a