3.8" 1.4'' .................................... 5.8'' 3.8'' .................................... 11.4'' 1.2'' .................................... 21.2'' Figure 10. Blade width radii. -20 For Machines Mfg. Since 8/09 OPERATION Model SB1021/SB1022 Tooth Set Three common tooth sets are alternate, wavy, and raker (see Figure 11). Each removes material in a different manner to make the kerf in the workpiece. Alternate Wavy Raker Figure 11. Bandsaw blade tooth sets. Alternate: An all-purpose arrangem

Repeat this process and move the carriage left/ right and the cross slide forward/backward to distribute oil along the way guides. Lubricate the guides once before and once after operating the lathe. If the lathe is in a moist or dirty environment, increase the lubrication interval and make sure to keep the oil level full. . Location of way pump, fill plug, and sight glass on the apron. Sight Glass Fill Plug Way Pump Unpainted & Machined Surfaces Besides the ways and leadscrew, all other unpaint

• Secure Clamping: A thrown workpiece may cause severe injury or even death. When swapping the chuck jaw positions, use a torque wrench to re-torque the M8-1.25 jaw mounting cap screws to 29 ft/lbs. When clamping a workpiece, maximum gripping force is attained at full jaw and scroll gear engagement. If the jaw and scroll gear are partially engaged, clamping force is reduced. • Chuck Speed Rating: Exceeding the maximum rated speed indicated on the chuck, or using excessive spindle speeds with an

Figure 63. Thread dial gear engaged with leadscrew. Cap Screw Dial Gear -43 Figure 67 Model SB1001 8K™ Lathe OP E R A T ION For Machines Mfg. Since 8/11 When threading, we recommend using the slowest speed possible and avoiding deep cuts, so you can more easily disengage the half nut to prevent an apron crash! Thread Dial Chart Find the TPI (threads per inch) that you want to cut in the left column of the thread dial chart (see Figure 64), then reference the dial number to the right of it. The d

Ignoring this warning can lead to a severe crushing injury or finger amputation! Figure 1. Features. Manufactured with high-tech German CNC machinery. Grease fitting for complete internal lubrication. Universal plain-back mounting. Hardened steel jaws for durability and extreme clamping force and grip. Two-piece jaws for speedy internal/external clamping changes. Designed for up to 2000 RPM. Specifications • OD Clamping Range...0.32"-6.30" (8-160mm) • ID Clamping Range ..2.17"-5.90" (55-150mm) •

15, 2001, check and AT CIRCUIT BREAKER. Is “CHECK WATER LEVEL” light on with door closed? Check all main fuses or circuit breaker, replace as necessary. Unit not heating up properly, or not cooking as fast, “ON” light lit. No Yes Drain unit. Turn unit on with door open. Add two gallons of water THROUGH TROUGH. Close door. Wait 10 minutes. Open door. Depress and hold door switch. Does unit have water? Add water according to start- up instructions on door. Wait 5 minutes, light should go off. Is b

Except for the differences noted in this insert, all other content in the Model SB1014 Owner’s Manual applies to this machine. Before operating your new lathe, you MUST read and understand this insert, the entire Model SB1014 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of injury when using this machine. Keep this insert for later reference. If you have any further questions about this manual insert or the differences between the Model SB1014F and the Model SB1014, contact

5. Cover and place the machine in a dry area that is out of direct sunlight and away from hazardous fumes, paint, solvents, or gas. Fumes and sunlight can bleach or discolor paint and make plastic guards cloudy. 6. Once or twice a month, depending on the ambient humidity levels in the storage environment, wipe down the machine as outlined in Step 3. 7. Every few months, start the machine and run all gear-driven components for a few minutes. This will keep the bearings, bushings, gears, and shaft

However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure the best possible results from your new machine. Step-by-step instructions for these adjustments can be found on the pages referenced below. Factory adjustments that should be verified: ... ..........................................Page 34). ... ................................................................... adjustment (Page 65). ... .......................

( For best results, no more than 3 racks should be used) Blower Fan and Motor: 1/3 hp, 1725 rpm, 60 cycle, 115V AC, high efficiency, permanent split phase motor with permanent lubricated ball bearings, overload protection and Class “B” insulation. Motor mounted to rear of oven. Motor serviceable from front of oven through oven cavity. Electrical System: Wired for single phase, 115V AC with 6’ cord and 3-prong plug supplied with each deck. Gas Control System: Includes pressure regulator, flame sw