How To Install The Batteries 1. On the bottom of the portable chime you will find a round battery release tab. Push the tab inward and slide the cover in the direction of the arrow. The battery cover will slide off. Battery Release Tab 2. Install 4 C-cell batteries (we recommend Alkaline Batteries) 3. Remove back of wireless push button and install the 12-volt battery (included) as shown below. Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each pus

These adjustments can be made with BEA’s universal remote control. Other accessories available for the Eagle include the false ceiling adapter (ECA), and the rain protection cover (ERA). PRELIMINARY TECHNICAL SPECIFICATIONS Frequency: 24.125 GHz Supply voltage: 12 to 24 V AC : ± 10% : 12 to 24 V DC : -10% / +30% : Mounting height: 16.5 feet Tilt angle: 0° to 90° vertical -30° to +30° lateral Detection area: 13.1 ft x 8.2 ft Minimum detection speed: 2in/sec. (measured in axis) Power consumption:

1 SAF. 2 RTN KM K GREEN WHITE RED YELLOW WHITE STANLEY "L" ORANGE YELLOW RED BLUE YELLOW STANLEY M/P 2 1, В 7 7 1, В STANLEY 521 TB4-5 TB4-4 TB4^ TB4-10 TB4-9 TORMAXTDA 2 1,3, б, В В & 9 7 1, 3, б, В LO-LINX 24 VAC MTR STALL SENSORS AUX 0 STALL 1 О 0 STALL 2 0 0 EAGLE 1 0 EAGLE 2 Odoor mtd 0 SENSOR 1 Odoor mtd 0 SENSOR 2 О BODY-0 GUARD О 5 2 8 О © Ж1 lli] HI HR 24 V TRANSFORMER i S DC MOTOR SEE NOTE #1 Pre-wired switch assembly AUTO RED GREEN WHITE BLACK a Ш cr GREEN WHI

Remove the battery cover on the chime. 2. Remove the white Styrofoam block 3. Unplug the red and black wires inside the battery compartment. 4. Remove the battery pack and discard appropriately. StyrofoamBlock House Code Door Try-Me Wires Chime components Required Tools: Small flat blade screwdriver, drill, 1/16” and 5/32” drill bits, and phillips screwdriver. Included Hardware: (2) Plastic screw anchors (2) 4x20mm screws (2) 3x20mm screws (2) Double sided adhesive pads The wireless door chime K

Remove the screw and take off the door. 4. Locate the chime and pushbutton jumpers shown below. Push Button Jumpers Chime Jumpers 5. Jumpers 1-6 are used to select 1 of 64 possible home security codes. 6. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then test the system for proper operation. Positions 1-6 on the chime and pushbutton must match exactly. Push Button Mounting Instructions Note: Avoid mounting the push button on

Included Hardware: (2) Plastic screw anchors (2) 4x20mm screws (for anchors) (2) 3x20mm screws (2) Double sided adhesive pads The wireless door chime Kit has two components: Chime (receiver) Push-Button (Transmitter). Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each push button is set with jumpers 7-9. Single Push Button Kit: If you purchased a kit with a single push button, the chime tune will be set to Ding Dong from the factory. Dual Push Butt

All Rights Reserved. Restricted Rights Legend This software and documentation is subject to and made available only pursuant to the terms of the BEA Systems License Agreement and may be used or copied only in accordance with the terms of that agreement. It is against the law to copy the software except as specifically allowed in the agreement. This document may not, in whole or in part, be copied photocopied, reproduced, translated, or reduced to any electronic medium or machine readable form wi

2 Technical Specifications DESCRIPTION SPECIFICATION Frequency: 12 to 24 V AC: ± 10%: 12 to 24 V DC: -10% / +30%: 24.125 GHz Supply voltage: Mounting height: Normal: 7’; Maximum: 10’-0” Tilt angle: 0° to 90° vertical -15° to +15° lateral Detection area: Wide 13ft (W) x 6.5ft (D) Narrow 6.5ft (W) x 8.2ft (D) (supplied as optional) Minimum detection speed: 2 in/sec. (measured in axis) Power consumption: < 2 W Standard output relay: Max contact voltage 60 VDC / 125 VAC Max contact current 1 A (resi