Always place vacuum cleaner on the floor with handle in upright position when using tools. Never place your fingers under the cleaner when it is running. Never place powerfoot on furniture or uneven surfaces. Do not place vacuum cleaner close enough to objects to pull them into rotating brush. 9 800.237.7691 Maintenance and care to maximize your cleaning performance and extend the life of your vacuum, it is very important that you empty your dirt container and check and clean your filters freque

Remove the cord and plug it into an electrical outlet. There are two quick release cord wraps for easy cord removal, and a cord clip that is part of the upper cord wrap where you can attach the cord when vacuuming. 2. When finished cleaning, turn vacuum cleaner off. Unplug power cord by grasping the polarized plug (NOT the cord) and disconnect from outlet. 3. Return Quick Release cord wrap to original position and loop power cord around cord wrap. Clip molded plug to power cord to secure. 6 Quic

............................................3-8 Accessory Tool Usage. ...................................... 3-10 MAINTENANCE Periodic Maintenance...........................................4-1 Daily/ Regular Maintenance.................................4-2 Vacuum Motor Replacement ...............................4-3 Belt Replacement.................................................4-4 Solution Pump Replacement................................4-5 Wiring Diagram. ......................................

Take care not to run over loose objects oredges of area rugs. Stallingbrush may result in premature belt failure. Tip: make only one trip to the sink by removing the entire portable cleaner. fill and empty in the same trip. 4. 2. 3. WARNING: to reduce the risk of fire, electric shock, or injury, turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting. Tip: for best results empty, rinse and dry both tanks before storing. 800.237.7691 9 Operations

If that is needed, please follow the instructions below. 1. turn off the machine, and unplug it from the outlet. Remove portable spot cleaner. 2. Remove the nozzle by unscrewing three WARNING: to reduce the risk of fire, electric shock or injury, unplug from the outletbefore servicing. screws on the nozzle cover. 3. turn the machine on its side. ImPORTANT: with portable spot cleaning pedal facing down. 4. Remove end cap by unscrewing the 3 screws. take care not to drop the screws into the unit.

The portable spot cleaner detaches to clean tough spots and stains and hard to reach areas. Hot water heater This deep cleaner features a patented built-in hot water heater which will heat the hot tap water you put in to safely optimize cleaning effectiveness. The heater temperature is limited to prevent carpet damage. The heater automatically turns on when you turn the machine on. This operates only in upright cleaning mode. Scotchgard™ Protector Carpet protection applied at the mill typically

2. using the brush on the tool, gently scrub the area to be cleaned. 3. apply downward pressure on the tool and pull it toward you. the suction will remove the dirt and cleaning solution. continue until no more dirt can be removed. Adsdfdd ghg bvhcvbbj jkn hnbjgcghh fhl kl Manufacturer’s tag ImPORTANT Check for colorfastness in an inconspicuous place. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric 800.237.7691 11 Operations Portable spot cleaning mode continued

NOTE: When charging, the Spot Lifter and charger may become warm to the touch. This is normal and no cause for concern. 2. Spot Lifter must be in “ O ” (OFF) position to charge. 3. When completely charged, your Spot Lifter will operate for up to 7 minutes for model 1718 and up to 15 minutes for model 1719. When completely discharged, it will take approximately 12 hours to fully recharge. Tip: For maximum battery life, completely discharge and recharge Spot Lifter every 1-2 months. Tip: After uni

Refill if needed. cleaning solution and remove any Never run dry. surface soil. Using the brush before applying solution can push soil more deeply into carpet. Spot cleaning upholstery 1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your Spot Lifter. If tag is coded with an “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. 2. If manufacturer’s tag is missing or not coded, check with your furniture dealer. NOTE: If possible, check