Do not disturb sensor scanning procedure (wait until water flow stops and LED switches off) Replace electronics module (See “Replacement Parts”) Change mode or reset sensor (See “Care and Maintenance”) Check external water pressure Provide pressure between 20 - 125 psi Replace solenoid valve (See “Replacement Parts”) Replace electronics module (See “Replacement Parts”) Water runs continuously Water fl ows although shut-off screw is inoperable removed Water drops on infrared window Infrared windo

1 Enable “Manual Setting” Mode > See “Enabling Manual Setting Mode” section 2 Fully cover sensor with hand. Water fl ow stops after 5 seconds - Continue to hold on for another four (4) additional water pulses. 3 Remove hand. Result: Scrub Mode is now activated for 180 seconds. F - Sensor Range Adjustment The detection distance of the sensor can be adjusted between approximately 4 - 11 inches from the infrared window. 1 Enable “Manual Setting” Mode > See “Enabling Manual Setting Mode” section 2 R

. . . . . . . . . . . . . . . . . . . . . . . . . .9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 10 Care and Maintenance . . . . . . . . . . . . . . . . . 12 Multi-Faucet Transformer Wiring . . . . . . . . . 14 IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with the installation, file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installer. Se

Possible solenoid contamination could occur and will void any warranty. Mounting of Lavatory and Gooseneck Faucet Prerequisites • Supply valve is installed • Water supply lines are fl ushed properly • For AC faucets, power outlet is installed It is not necessary to unscrew the connection between braided hose and housing to install the product. Do not remove protective covering from sensor until starting up faucet operation. Do not tighten locknut before step 4 is completed. 1 Mount cover plate i

The hardware, firmware, or software described in this document is subject to change without notice. IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES. Enterasys Networks, Inc. 50

Box 309, Menomonee Falls, WI 53052-0309 Phone: 1-800-BRADLEY Fax: (262) 251-5817 http:\\215-1187 Rev N; EN 06-915B © 2007 Bradley Corporation Page 1 of 85 4/6/2007 IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with theinstallation, file this manual with the owner or maintenance department. Separate parts from packaging and make sure all parts are accounted for beforediscarding any packaging material. If any parts are missing, do not begin installati

Provide adequate supports (by installer) for supply pipe using pipe hangers or other means. 2. Connect drain piping to 1." NPT drain outlet on unit (piping by installer). 3. Hang the safety sign from the unit with the curtain hooks provided (or mount it to the wall using signmounting hardware by installer). NOTE: All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1.8" (3mm) per threaded joint. To fi nd the tolerance of a dimension, add the number of threa

T; ECM 09-05-0019 © 2009 Bradley Corporation Page 1 of 13 8/11/09 S19-310PVC Combination Drench Shower and Eye/Face Wash Combine douche oculaire/faciale Combinacion de ducha de aspersion y lavador de ojos/rostro Table of Contents Pre-Installation Information . . . . . . . . . . . . . . 2 Installation Instructions. . . . . . . . . . . . . . . . . . 3 Assembly of Components . . . . . . . . . . . . . . . 4 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Table des matieres Avant

. . . . . . . . . . . . . . . .2 Model TDB3104 Washfountain Dimensions . . . . 3 Model WF3204 Washfountain Dimensions . . . . . .4 Washfountain Rough-Ins . . . . . . . . . . . . . . . . . .5-7 Drain Installation . . . . . . . . . . . . . . . . . . . . . . . . . .8 Bowl/Pedestal Mounting and Assembly . . . . . . . .9 Drain Spud Installation . . . . . . . . . . . . . . . . . . . . .10 Air Valve Installation (A/O drains) . . . . . . . . .11-12 Air Valve Installation (B/H drains) . . . . . . . . .13

For more than three washfountains, pipe sizes should be increased proportionately. -Supplies from below or through wall - Vented through ceiling off trap inside pedestal Type O Drain -Supplies from above - Vented from below or through wall off drain (mm) Figure 2d NOTE: Supply lines for one to two washfountains should be 1”; for three washfountains, 1-1/4”. For more than three washfountains, pipe sizes should be increased proportionately. Bradley Corporation • 215-1470 Rev. H; EN 06-915 2/8/07 T