These characters are available in fonts 1–6 and 9. Getting Started 13 _______________________________________________________________________ 14 Getting Started 2.4 Memory Cartridges The Printer has one standard memory cartridge slot. The primary use of the memory cartridges is for storing label formats, graphic images, fonts and for internal batch. Follow the instructions outlined below when installing memory cartridges. 1. Ensure that all printing has been completed. 2. Open the Side Access Co

At power up or in an idle condition, this value should be in the range of 060 to 065. A reading of 175 is high and could decrease the life of the printhead. An average amount of printing will give readings that range from 070 to 120. Pot -this reading comes from the darkness potentiometer located on the front panel board. It will vary from 000 (darkest) to 255 (lightest). Adjust this value for a midrange value of 128. TOFA -(Top of Form Adjustment) determines where the first position of print be

Customer order # 11342L-12 Manufacturer part # 11342LB-12 Rev. 1 . This manual contains proprietary information of Brady Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Brady Corporation. . Continuous improvement of products is a policy of Brady Corporat

A sample printout is shown in Figure 34 on page 81. NOTES on diagnostic printouts: • FE indicates a framing error. • OE indicates an overrun error. • PE indicates a parity error. • NE indicates noise. For any errors, check that your communication parameters are correct. Set the print width equal to or less than the label width used for the test. See page 46 for more information. Bradyprinter 200M-e and 200M-e 300 User’s Guide Selecting Prefix and Delimiter Characters Prefix and delimiter charact

While every precaution has been taken in preparation of this document, Brady assumes no liability to any party for any loss or damage caused by errors or omissions or by statements resulting from negligence, accident, or any other cause. Brady further assumes no liability arising out of the application or use of any product or system described, herein; nor any liability for incidental or consequential damages arising from the use of this document. Brady disclaims all warranties of merchantabilit

Brady Co. Automatic Indentification Products CG Triumvirate is a trademark of Agfa Corporation. Corrupad is a Trademark of Corrupad Protective Packaging Inc. Bradyprinter THT Model 1024 is a Trademark of Brady USA Inc. As an Energy Star Partner, Brady USA Inc. has determined that this product meets the Energy Star guidelines for energy efficiency. Information in this document is subject to change without notice and does not represent a commitment on the part of Brady USA Inc. No part of this man

H. BRADY CO. AUTOMATIC IDENTIFICATION PRODUCTS Bradyprinte. T. TH. Mode. 200. an. 260. Therma. Transfe. Printe. USER'. GUID. Custome. par. #31450L-1. Manufacture. par. . 31450LB-1. Rev. . W. H. BRAD. CO. AUTOMATI. IDENTIFICATIO. PRODUCT. Proprietary Statement . This manual contains proprietary information of Brady USA, Inc. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduce

(Fo. Serial-Interfac. Printer. Only. The M-Series Printer, with the RS-232 Serial Interface, uses eight miniature switches located on the rear of the printer, above the Signal Interface Cable Connector. The ON/OFF positions of these switches establish some of the Printer Configuration Parameters. Bank 1 switches must be properly positioned to establish serial data communications with the host computer. Thereafter, the position of these switches should not be changed. Note: Parallel-interface pri

Check the display screen for more information. CHECK RIBBON Off Normal operation — ribbon (if used) is properly loaded. On Printing is paused, the front panel displays a warning message, and the PAUSE light is on. • If the printer is in direct thermal mode: Ribbon is loaded. • If the printer is in thermal transfer mode: No ribbon is loaded. PAPER OUT Off Normal operation — media is properly loaded. On No media is under the media sensor. Printing is paused, the display shows an error message, and

See page 16. Calibrate the printer (see page 17). Brady X-PLUS Series User.s Guide Error Condition Head Open Problem Solution The printhead is not fully closed. Close the printhead. Error Condition Head Element Bad Problem Solution One or more of the printhead elements have failed the printhead element test. If the failed elements impact your printing application, replace the printhead. To override this error, disable the head test count feature on the front panel by defaulting the value to .000