A Kit Includes: Installation: 1. Remove the original bulb connector from the back side of the housing. 2. Remove the tail light housing from the vehicle. 3. On the Chevelle, remove the chrome tail light cover. There are four nuts on the back side of the housing. 4. Remove the tail light lens. On the Camaro there are five screws and one metal clip on the back side of the housing. 5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 6. Remove th

UTV-1500 Gauge for Polaris RZR MPHABTEMPOILkm/hEFVOLTSFUEL1234567SERVHRTachometer bar graphSpeed displayLight sensor locationMessage centerSpeed unit indicators4x4 on indicatorCheck engine indicatorGear position indicatorsFuel bar graph Operation menu Switch functions: Pressing the switch during normal gauge operation will move the message center through the below display functions. ... Odometer ... A Trip odometer A (hold switch to reset) ... B Trip odometer B (hold switch to reset) SERV ......

Remove the clusters from the vehicle. The procedure for the speedometer and tachometer clusters are the same, but only one side is shown in the photos. 2. Remove the three screws holding the bezel on to the gauge can. Two are indicated by the upper arrows in the photo at right; one is on the bottom side of the can and cannot be seen here. After the bezel is set aside, remove the two screws near the center of the can to remove the original gauge. On the speedometer can (shown) you will also need

This module can be used as a simple clock display or it can display data from any BIM module attached to the system as well as several gauge values from the control box sensors. Most versions of this module come with at least one switch in the face to allow the display to change between various screens. Some versions may also contain two additional switches in the face which can be used as the SW1 and SW2 for the VHX control box with the use of the switch harness provided with it. CONNECTION: Th

There are four screws holding each lens in place. 2. Remove the light bulbs. 3. Now is a good time to clean the lenses and housings. If lenses are in bad shape a new set is recommended. 4. DO NOT remove the tape from the LED assemblies yet! MAN#650203 5. Test fit the assembly into the tail light housing as shown below to make sure it aligns correctly. 6. Before mounting the new LED assembly into the housing, plug the bulb base into the stock bulb socket and test the tail lights and flasher

B Kit Includes: m, m Installation: 1. Remove the screws and the tail light lens. 2. Remove the tail light bulb. 3. Now is a good time to clean or replace the lens and housing if necessary. 4. The new LED assembly will mount into the original light bulb socket. Push it into the socket and turn it clockwise to lock it in. 5. Repeat for the other tail light. 6. Test the tail lights, brake lights, and turn signals. If the turn signals do not flash, you will need to upgrade your flasher. If

If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside of the housing.The flat side of the mounting disk should betoward the outsideand thes

B Kit Includes: Installation: 1. Remove the two screws and tail light lens. 2. Remove the light bulb. 3. Push and twist to remove the plastic wire socket from the back side of the housing. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the nut and round metal spacer from the back of the new LED assembly. MAN#650188 rev. B 6. Insert the new LED assembly through the hole where the original bulb and connector were. Use caution whe

4. Remove the tail light lens. 5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside o

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. The housing may need to be removed from the car on the ’71-’72 Chevelle. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the screw and aluminum back plate from the back of the new LED assembly. LED assembly standard back back for ‘71-‘72 Chevelle (attached to the assembly) (packaged separately) 6. Insert