Failure to follow all instructions listed below may result in personal injury. SAVE THESE INSTRUCTIONS Safety Rules for Mini Saw Attachment ! DANGER Keep hands away from cutting area and blade. Keep your second hand on motor housing. If both hands are holding the tool, they cannot be cut by the blade. Hold the tool firmly to prevent loss of control. Figures in this manual illustrate typical hand support of the tool. NEVER place your hand behind the saw blade since kickback could cause the saw to

Box 1468 Racine, Wisconsin 53401 1-800-437-3635 Dremel brand products are manufactured and sold by the Dremel Division of Robert Bosch Tool Corporation 2 610 925 737 2/05 PRINTED IN U.S.A. IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING KEEP AWAY FROM WATER DANGER – To reduce the risk of electrocution: 1. Do not place or store appli

Box 1468 Racine, Wisconsin 53401 Call Toll Free for Consumer Information & Service Locations Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit Llame gratis para obtener información para el consumidor y ubicaciones de servicio 1-800-4-DREMEL (1-800-437-3635) For English Version See page 2 Version française Voir page 23 Versión en español Ver la página 45 DM 2610015339 05-11:DM 2610015339 05-11.qxp 5/№/11 9:40 AM Page 2 General

Other accessories are not designed for this tool and may lead to personal injury or property damage. The number and variety of accessories for the Rotary Tool are almost limitless. There is a category suited to almost any job you might have to do — and a variety of sizes and shapes within each category which enables you to get the perfect accessory for every need. Refer to the DREMEL ACCESSORY ORDER FORM for illustrations of the accessories available. These accessories may be found at your loc

Such preventive safety measures reduce the risk of starting the tool accidentally. A WARNING Models 100 & 200 High Speed Rotary Tools SWITCH (100 SINGLE SPEED) (200 TWO SPEED) COLLET. WRENCH -eC Model 3000 High Speed Rotary Tool EZ TWIST™ SHAFT LOCK INTEGRATED BUTTON WRENCH/NOSE CAP (Model 3000 only) ON/OFF SWITCH HANGER COLLET NUT CORD VENTILATION OPENINGS VENTILATION OPENINGS BRUSH COVER (one on each side) Model number Voltage rating Amperage rating No load speed Collet cap

Street Racine Racine, WI 53406 M-F, 7am - 7pm CST California 1-800-275-2052 1-760-327-3003 1-760-322-3972 Dremel Authorized Service 4631 E. Sunny Dunes Palm Springs, Ca 92264 M-F, 7am - 4:30pm PS" In CANADA Ontario 1-416-287-3000 1-416-287-3005 Giles Tool Agencies 47 Granger Avenue Scarborough, ON M1K 3K9 M-F, 8:30am - 5pm ES‘ Quebec (Quebec City) 1-418-877-3371 1-418-877-3958 Clinique D'Outillage M.P. 3075 boul. Hamel, Suite 107 Quebec, QC G1P 4C8 M-F, 8am - 12pm, 1-5pm EST

!WARNING It is important to read and understand the section in this manual called “Kickback and Related Warnings”. FIG.4PADDLESWITCH"LOCK-ON" BUTTON"LOCK-OFF"SWITCHRELEASE LEVER DEPTH ADJUSTMENT DEPTH Disconnect plug from power source. Loosen the depth adjustment lever located on the right side of the tool. The foot is spring loaded and will lower automatically (Fig. 5). Tighten lever counter clockwise at the depth FIG. 5 setting desired. Check desired depth (Fig. 5). DEPTHSCALEADJUSTMENTLEVER L

This is not common, but it does happen. Practice on scrap materials first to see how the Moto-Tool cuts. Keep in mind that the work']s done by the speed of the tool and by the accessory in the chuck. You should not lean on or push the tool into the work. Instead, lower the spinning accessory lightly to the work and allow it to touch the point at. which you want cutting (or sanding or etch-" ing, etc.) to begin. Concentrate'on guiding the tool over the work using very little pros- sure from your

Pernaps you should be using a different cutter, and perhaps an adjustment in speed would solve the problem. But lean ing on the tool seldoms helps. Speed Settings " Speed for light cuts, caution burning on deep grooves. t" Depending on cutting direction relative to grain. CATALOG NUMBER I WOOD WOOD PLJ_STIC BRASS, ETO, STONE CERAMIC tI HIGH SPEED CUTTERS 100. 121.131.141 5. 5 3 t 2 4 114.124,134.144 5 3 2 t 1-2 2 189.190 5 5 2 4 5 118.191.193 5 5 2 3 5 192,194 5 5 2 3 5 118,117,125,196 5 3 2 2 2

It will give youtips on some of the many different do-it-yourself jobs the tool will perform around your home and workshop. WARNING For your own safety read your Owner's Manual assembly • operation • safety instructions. before operating your Dremel Moto-Tool OREMEL _.o.,o_ _ Racine, Wisconsin 53401 1/88 PRINTED IN U.S.A. 5296077 When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, For Your Safety... electric shock, and personal injury, includ