Log:

Harbor Freight Tools 93601

Téléchargements : 0 Taille : 12 mb    Fabricant : Harbor Freight Tools  
Catégorie : Autres outils

Page 2 10. Always check hardware and assembled parts after assembling. All connections should be tight and hardware tightened. 11. Caution: Avoid sharp edges during use and assembly. 12. Beware of operating the power tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or sawdust. Electrical products create sparks which may ignite sawdust released from the Dust Collector, as well as other dust and fumes. 13. Carefully inspect the condition of the accessory before u

Harbor Freight Tools 93098

Téléchargements : 1 Taille : 9 mb    Fabricant : Harbor Freight Tools  
Catégorie : Autres accessoires pour la maison

Do not modify this Solar Light and do not use this Solar Light for a purpose for which it was not intended. 13. Do not set up the Solar Light if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not set up the Solar Light. 14. Keep the Solar Panel free of dirt, dust and grime. Dust covering the Solar Panel will block out sunlight causing a decrease or stoppage of effi

Harbor Freight Tools 46240-B

Téléchargements : 0 Taille : 9 mb    Fabricant : Harbor Freight Tools  
Catégorie : Clouteuses

Connect the Air Source Hose to the Air Plug (41). Note: If you are not using an automatic oiler system on your air compressor, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Remove the air line at the inlet and put 2 or 3 drops of good quality air tool oil into the air fitting each day of use. With heavy, prolonged use, do this at least twice a day. 2. Set the air pressure on your compressor to 60-125 PSI. Do not exceed the maximum air pressure of 125 PSI. Not

Harbor Freight Tools 93827

Téléchargements : 0 Taille : 8 mb    Fabricant : Harbor Freight Tools  
Catégorie : Jig Saw et

Be sure to keep your fingers well away from the Trigger (4), Safety (21), and Blade (10) while performing any adjustment, but especially when adjusting the Depth, because the battery may be installed. B. Loosen the Depth Knob (34). C. Raise/lower the Saw body in relation to the Foot (35) to adjust the depth. Note: Add 1/8” to the depth so the Saw Blade (10) can cut through the material cleanly. D. Retighten the Depth Knob (34) securely. 5. Make certain that both halves of the workpiece are prope

Harbor Freight Tools 93212

Téléchargements : 17 Taille : 8 mb    Fabricant : Harbor Freight Tools  
Catégorie : Machines-outils

Release pressure. The Fuse Holder will be flush with the rim of the Fuse Holder Socket. REV 10b Troubleshooting Problem Possible Causes Likely Solutions Motor and Electrical Lathe will not start or a breaker trips on startup. Cord not connected.1. No power at outlet. 2. Fuse has blown. 3. Chuck Guard safety interlock not 4. in place. PC Board (182) faulty.5. Power Switch (178), Forward/6. OFF/Reverse Switch (181) and/ or Speed Control Knob (180) not working. Internal damage or wear. (such 7. as

Harbor Freight Tools 93179

Téléchargements : 1 Taille : 8 mb    Fabricant : Harbor Freight Tools  
Catégorie : Les machines à rectifier

6. Always use 2 hands during use. 7. WARNING! All accessories for this tool must be rated for at least 6500 RPM. Grinding wheels and other accessories running over their rated speed can fly apart and cause injury. 8. Use only 9” diameter grinding wheels having a 5/8” or ( 7/8” if using included arbor adaptor) center mounting hole. Never disable or modify the wheel guard. 9. WARNING! Never install a carbide tipped or steel circular saw blade for use in this tool. Never install a wood carving blad

Harbor Freight Tools 32650

Téléchargements : 3 Taille : 7 mb    Fabricant : Harbor Freight Tools  
Catégorie : Menuisiers Plate

Accessory Diameter 2” Shank Diameter Router: 1/4” Shaper: 1/2” Table Top 11-3/4” x 9-3/4” surface Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. Components Figure 1Table Insert (8) Carbon Brushes (3b) Belt (34) Double Ended Wrench (55) Nut (49) Spindle Wrench (54) Keyed Washer (48) Switch Key (27b) Washer (13) Radius Pin (6) Collar (53) Router Bit Collet (50) Sh

Harbor Freight Tools 93830

Téléchargements : 4 Taille : 6 mb    Fabricant : Harbor Freight Tools  
Catégorie : Jig Saw et

Never attempt to discharge a tool’s battery by continuing to pull the tool trigger. When tool performance begins to diminish, stop the tool, recharge the battery and use the fresh battery for optimal performance. 1. When a Battery (47) requires recharging, a 3 to 5 hour* charge allows the tool to operate at full power. Do not recharge the Battery longer than 5 hours*, as damage to the Battery and/or tool will occur. 2. To charge the Battery (47), plug the AC Charger Adapter’s (53) plug into the

Harbor Freight Tools 31849

Téléchargements : 0 Taille : 6 mb    Fabricant : Harbor Freight Tools  
Catégorie : Menuisiers Plate

Before assembling, remove all traces of the packing grease from the Jointer and wipe all parts thoroughly with a clean dry cloth. When cleaning do not use acetone, gasoline or paint thinner as these solvents are dangerous to you and may also cause damage to plastic and rubber parts. Apply a thin coating of automotive wax to any unpainted surfaces to prevent rust. Caution!: Consider the weight of the components and take the necessary precautions when lifting. Assistance may be required during ass

Harbor Freight Tools ROUTER WITH FULL SIZE TABLE 91130

Téléchargements : 8 Taille : 5 mb    Fabricant : Harbor Freight Tools  
Catégorie : Menuisiers Plate

Make sure the Nuts are above the mounting holes. Then, screw a Nut (24B) upward on each of the eight Hex Screws to secure the Hex Screws to the Main Table. (See Figure J.) To AttachThe Motor Assembly: 1. Lower the Adjustment Board (17D) with its pre-attached Motor Assembly through the top of the Main Table (20B). Position the Adjustment Board and Motor Assembly so that its Power Cord is on the left hand side and the Spindle Lock Lever (22E) is on the right hand side. Continue lowering the Adjust





catégories