\\ ...... 7" 1. Turn the handwhee:! Se the shuttle forms a half moon on the:i:ft::iae of the ma: i 2. Hold the shuttle '.,_:_ i tinter pi_ _d position the shuttle so it forms a:R i : i i_ht side. The hook _8_will be on the .......... 3. Put the shuttle race cover _, back into place over the shuttle assembly. 4. Snap the levers ,,_,_2b_, position. back into the original J 7O Limpieza de la corredera de la lanzadera Nettoyage de la coursi_re Esta area debera mantenerse tibre de polvo, petusa y de

Remote Control 2.2. Indoor Unit 2.3. Outdoor unit 3 Product Specifications 4 Dimensions 4.1. Indoor Unit / Remote Control 4.2. Outdoor Unit 5 Refrigeration Cycle Diagram 6 Block Diagram 7 Wiring Diagram 7.1. Indoor Unit Page Page 2 7.2. Outdoor Unit 153 8 Electronic Circuit Diagram 163 8.1. Indoor Unit / Remote Controller 164 8.2. Outdoor Unit 185 9 Operation Details 206 9.1. Basic Function 2010 9.2. Indoor Power Relay Control 2110 9.3. Room Temperature Control (Compressor Control) 2211 9.4. Air

Draw the bobbin thread up through the fabric by holding the top thread and taking one stitch at the spot where you wish to start darning. Lowering the presser bar, start sewing at a slow to medium speed. Move the fabric back and forth with _a steady rhythm to cover the darning area. When it is covered, turn the fabric and sew another layer of stitching across the first layer of stitching. BUTTON SEWING SETTINGS Special Stitch Dial -ww_=-._ Feed Dogs -Down Zigzag Presser Foot Zigzag Needle Plate

Pull the spring wire loop up and past the top hook until the thread can be slipped into hook (See Fig. 2). When the thread is released, the spring wire loop will return to position (Fig. 3) with thread in proper place. Release spool of thread and hook thread into take up lever as shown (Fig. 4). Continue to thread machine exactly as shown. Needle must always be threaded in direction as shown in Fig. 5. Hold needle thread loosely in left hand and rotate hand wheel toward you one complete turn, Br

The stitch is decora tive as well as useful, Simply stitch the elastic into place around the waist of the garment, making sure that the elastic is evenly spaced. To do this mark the correct length piece into quarters and match these markings with center front and back of the gar ment as well as side seams. After the basic construction of your garment is finished, there are still many finishing touches to be done. To aid your completion of your garment, the Kenmore has been designed to do the fol

Now that you are familiar with the controls on your machine and with the accessories provided for the machine, you are ready to start to sew with your new Kenmore sewing machine. Below are some good habits to follow each time you sit down to sew: , Test the needle -it should be straight, properly set and sharp on the point, It should be the correct size for the fabric and thread being used. Do not be afraid to change your needle frequently. Many of the new fabrics made of synthetic blends tend t

Insufficient pressure may cause poor feeding of the fabric, skipped stitches, or difficulty in guiding the fabric. If feed dogs or presser foot marks appear on the fabric, reduce the pressure. When sewing multiple thickness or heavy fabric, reduce the pressure. Increase pressure when sewing lighter weight fabrics. FEED DOG CONTROL There are a few times when you want to control the feeding of the fabric yourself. Remove the base cover from the base. Pull down the feed dog control or turn to the l

, KNOWING YOUR SEWING MACHINE Identifying Parts ................................................. 2, 3 Installing Machine ............................................... 4, 5 Converting to Free-arm Sewing ................................ 6 Winding the Bobbin ............................................... 7 Threading the Bobbin Case ...................................... 8 Threading of Top Thread ........................................ 9 USING THE CONTROLS Adjusting Top Tension ................

Ensure the hooks are properly seated on the installation plate by moving in left and right. Indoor unit Hooks at installation plate Sleeve for piping hole Piping Drain hose ^Secure the Indoor Unit ^ 1. Tape the extra power supply cord in a bundle and keep it behind the chassis. • Ensure that the power supply cord is not clamped in between the unit's hook (2 positions) and installation plate. 2. Press the lower left and right side of the unit against the installation plate until hooks eng

RAC0502005C2 Service Manual Air Conditioner CS-TE9DKE CU-TE9DKE CS-TE12DKE CU-TE12DKE ссюш i|S î •