Start making the upper notch cut (C) on the side of the tree facing the felling direction (E). Be sure you don t make the lower cut too deep into the trunk. The notch (C) should be deep enough to create a hinge (F) of sufficient width and strength. The notch should be wide enough to direct the fall of the tree for as long as possible. OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Fig. 11 LIMBING Limbing a tree is the process of removing the branches from a fallen tree. Do not remove supporting l

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA This Act Seeks: “...to assure so far as possible every working man and woman in the nation safe and healthful working conditions and to preserve our human resources...” DUTIES Sec. 5 (a) Each employer— (1) shall furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or are likely to cause death or serious physical harm to his employees; (2)

Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information. Part No. 78413 Part No. 78608 Part No. 60873 Part No. 81067 PartNo.78786 15 TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* AMERICAN Bolt Head Markings Wren

In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel in the operation, transport, maintenance and storage of equipment. Lack of attention to safety can result in accident, per sonal injury, reduction of efficiency and worst of all—loss of life. Watch for safety hazards and correct defi ciencies promptly. Use the following safety precautions as a general guide to safe o

(Apply grease on smooth side of handle lock to aid in keeping lock in place until handle assembly is lowered into position.) Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. Rotate handle assembly down. Insert rear carriage bolt first, with bolt head on L.H. side of tiller and loosely assemble locknut (See Fig. 5). Insert pivot bolt in front part of plate and tighten. Cut down remaining corners of carton and lay

Avoid creating any source of ignition until gasoline ■ vapors have disappeared. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. 10 OPERATION JGINE (See Fig, 13) TILLING HINTS CAUTION: Keep drive control bar in “DISENGAGED” position when starting engine. When starting engine for the first time or if engine has run aut offuel, it will take extra pulls ofthe recoil starter to move fuel from the tank to the engine. » Make sure spark

To receive full value from the warranty, the operator must maintain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. • Once a year you should replace the spark plug, clean or replace air filter, and check tines and belts for wear. A new spark plug and clean airfilter assure proper air-fuel mixture and help y

316.350850 with CAUTION: Before using this • SAFETY product, read this manual and • ASSEMBLY follow all safety rules and oper• OPERATION ating instructions. • MAINTENANCE • PARTS LIST Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our website: 9096-31B206(2) date(08/06) TABLE OF CONTENTS TABLE OF CONTENTS Warranty Page 2 Maintenance and Repair Pages 15 - 21 Safety Rules Pages 3 - 8 Troubleshooting Page 22 Oil and Fuel Information Page 9 Specifications Page 23 Starting/Stopping I

A = Pull B = Solid objects C = Push Fig. 2 8 OIL AND FUEL INFORMATION OIL AND FUEL INFORMATION OIL AND FUEL MIXING INSTRUCTIONS Old and/or improperly mixed fuel are the main reasons for the unit not running properly. Be sure to use fresh (less than 60 days old) clean unleaded fuel. Follow the instructions carefully for the proper fuel/oil mixture. Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol, or MTBE (ether). Alcohol-blended fue

Si el arbol golpea cualquier red de servicio publico, la compania correspondiente debe ser notificada de inmediato. . Siempre corte con ambos pies bien apoyados en suelo solido para evitar perder el equilibrio. . No corte arriba de la altura del hombros, ya que si se tiene la sierra mas arriba de esa altura, es dificil de controlar bajo la fuerza del contragolpe. . No corte arboles cerca de cables electricos o de edificios. Deje tal operacion a los profesionales. . Corte solamente cuando al visi