No information contained herein may be copied, translated, transcribed or duplicated for any commercial purposes or disclosed to third parties in any form without the prior written consent of SAMSUNG Electronics Co., Ltd. TRADEMARKS OfficeServ 12 is the trademark of SAMSUNG Electronics Co., Ltd. Product names mentioned in this document may be trademarks and/or registered trademarks of their respective companies. Please read this guide before using the OfficeServ 12, and follow the instructions t

* Use only the specified AC adaptor (PSA-Series). Panel Description 2. CHECK Indicator This indicator shows whether an effect is ON/OFF, and also doubles as the Battery Check indicator. The indicator lights when an effect is ON. * If this indicator goes dim or no longer lights while an effect is ON, the battery is near exhaustion and should be replaced immediately. For instructions on changing the battery, refer to “Changing the Battery” (p. 12). * The CHECK indicator shows whether the effect is

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (separate sheet). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, this manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. A battery is supplied with the unit. The life of thi

Response1 (-3 dB): 100 Hz - 16 kHz Freq. Range1 (-10 dB): 70 Hz - 20 kHz Rotatable Coverage: 90° x 50° Rec. High-Pass Frequency: 90 Hz Passive Crossover Freq.: 2400 Hz Axial Sensitivity1: 94 dB (1 W/1 m) Max. Calculated SPL1: 125 dB Passive Power Handling2: 300 W continuous, 1200 W peak Impedance: 8 ohms (nominal), 6.0 ohms (min.) LF Transducers: Dual ICT-6.5-16, 6.5” (165mm) drivers HF Transducer: ICT-1-8, 1.3” (33mm) diaphragm compression driver Connectors: Single four-pin 12 AWG Phoenix/Euro

Using an AC adapter makes possible long performances with no worry about batteries going dead. GK IN Connector This connector is for connecting your guitar with a GK cable. NORMAL PU MIX Switch When Master is on, this switch determines whether or not the normal pickup sounds (or the sounds input to the GUITAR RETURN) are mixed. By mixing the normal pickup sound, you can create a sound that makes your guitar sound come alive. GUITAR OUT Jack Normal pickup signals input through the GK-2A are outpu

Now bassists also can enjoy using COSM Amp Modeling, COSM Overdrive/Distortion, and other high-quality modeling effects. ¦ More Powerful Vocal Tool Box Functions Pitch correction enables you to specify any desired time and corrective pitch within the song. And with Harmony Sequence, you can also specify the time and pitch for each of the harmony voices. ¦ Simplified Mastering Adjustments with the VALUE Dials You can adjust the amount and sonic quality of the Mastering Tool Kit, as well as the na

You can use it as a reminder of operational procedures. Main Uses Here are some ways in which the RC-20XL can be used. You can use your own creativity to come up with other ways to enjoy using the RC-20XL. ¦ “Sound On Sound” performance New “sound on sound” possibilities let you combine performances not only of guitar, but also vocals, percussion, and drum pads.................................................... p. 12 ¦ Create loop phrases You can record phrases from a sampling CD or MD, and ove

See Fig. 8. 2. Remove and retain secondary light and pod assembly by removing eight ( 8 ) OEM screws. See Figure 9. Figure 8 Figure 9 6 3. Attach four (4 ) pod mounting brackets (item 14 pg 2) to front and rear of bezel with four (4 ) 6-32 X 1/2" screws (item 4 pg 2) and four (4) 8-32 KEPS nuts (item 1 pg 2). See Figure 10. Figure 10 4. Install and secure O.E. bezel in overhead console (item 19 pg 2) with eight ( 8 ) # 6 X 3/8" PPH screws (item 2 pg 2) As shown. See Figure 11. Figure 11 7 5. Rem

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials / Tools required for this installation: 1. Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or scribe point tool or similar 4. Razor knife or similar tool 5. T-10TORX bit driver 6. 1/8" Drill Bit 7. Audiovox Series 640/650 Video Module FOR