SAFETY PRECAUTIONS FOR YOUR REFLEXOLOGY FOOT SPA. Please read this instruction booklet carefully before using your Reflexology Foot Spa. It will enable you to get the most out of your new product and to safely enjoy its many benefits. Please retain this booklet for future reference. 1. Diabetics and people with heart conditions or 7. Dry your hands thoroughly before connecting circulation problems must consult their health or disconnecting the plug from the power care practitioner before use out

Contents Pre-Delivery and Installation Checklist.................................................1 Portable Spa Site Preparation................................................................4 In-Ground Spa Site Preparation.............................................................4 Getting the Spa Into Your Yard...............................................................6 Electrical Requirements.........................................................................8 Electrical Requireme

Lay out the extension loom to verify that you have enough length to 4. reach the control box. Remember that conduit runs are not generally run in a straight line. Every bend, and up and down run consumes line length. Take this into consideration when verifying electrical and plumbing runs. Connect the extension loom to the control panel location on the circuit 5. board located inside the control box. You will also need to connect both the temperature and high limit sensors to the circuit board p

Wire runs over 85 feet must increase wire gauge to the next lower number. For example: A normal 50 amp RCD with four #8 AWG copper wires run over 85 feet would require you to go to four #6 AWG copper wires. Spa Model GFCI Required Wires Required Portable Spas All 230V spas (except 6205 control boxes requiring high amperage - see below) One 32 amp RCD or two 16 amp RCDs Four #10 AWG copper wires Spas with the 6300 control box (when high amperage is selected on circuit board) SEE CONFIGURATION INS

If the area receives direct sunlight, you will want to provide some • protection for the equipment portion of the equipment pack. The equipment pack and heater are delivered separately. Do not cover gas heaters unless properly vented. (See heater owner’s manual for important safety information.) Portable Spa Site Preparation Your spa needs a solid and level foundation. The area that it sits on must be able to support the weight of the spa, with water and the occupants who use it. If the foundati

Make sure the spa is positioned so that access to the equipment compartment and all side panels will not be blocked. Be certain that your installation will meet all city and local safety codes and requirements. Consider how you will use your spa How you intend to use your spa will help you determine where you should position it. For example, will you use your spa for recreational or therapeutic purposes? If your spa is mainly used for family recreation, be sure to leave plenty of room around it

This can be done by using one of the following techniques. Air Test The air test requires a wet/dry vacuum. Locate the plumbing line you wish to identify and secure the vacuum hose to cut open end. Turn on the vacuum, enter the spa and listen for vacuum suction sound from inside the spa side filter canister. If you hear the suction sound in the canister, the line is properly marked and can be connected to the suction side of the pump on the equipment pack. Water Test The water test requires a ga

It is a good idea to run the spa for at least 24 hours before pouring the concrete to insure there are no leaks. We understand you want to enjoy your spa now, but a 24-hour period with your spa running will let you know of any problems before they will be extremely hard to fix. The type of decking you have selected will have determined the grade of the spa. If you are pouring a regular deck up to the spas coping, then the top of the coping should be 4” above the surrounding area. In either event

Light niche and any metallic items in a 5’ (152 cm) radius must be properly bonded with #8 AWG grounding wire. Connect rigid conduit to the 3/4” hub located at the back of the light 1. niche and run to a water resistant junction box (or for 12 volt models to a low voltage transformer) no further than 25’ (7.6m). Remember this is a water cooled light, so the conduit and all connections must be leakproof. Feed the light cord through the rigid conduit to the junction box, leaving 2. at least 4 feet

If the slope is relatively minor, contact your local building safety. Site Excavation – Hard Bottom For hard bottom placement for in-ground spas, you will need a smooth and flat concrete surface at least 4” thick as large as the bottom contact points. Be sure not to seal the bottom off and making a sealed box. You will need adequate water drainage for escape under the spa. A gravel beds around the concrete base will help with this. Site Excavation – Sand Bottom With the spa area and all elevatio