General Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier. Loose coals are packed separately within the carton. When the heater is assembled the coals are placed on top off the fuel bed. The heaters is designed for use inset into a 407mm (16”) or 457mm (18”) wide by 559mm (22”) high fireplace opening see also section “Installation in a fire place opening”. A 2kw fan heater discreetly positioned in the canop

In daily use, switch on and wait for the ready light to illuminate. The water will then be at the correct temperature and the boiler ready to use. We recommend that you switch the power supply to the boiler off overnight and when the unit is not in use. OPERATION (WB5Eonly) After the electrical and water connections have been made, switch the power and water supply on. When the power supply is switched on, the small indicator lamp on the front panel will glow orange. This means that the water is

Fitting a scale reducer will help minimise scale. We regret that the manufacturers cannot be held responsible for scale problems even if a scale reducer has been installed. BOTTOM ENTRY Connect to a suitable cold drinking water supply using 15mm copper pipe and push on the ‘T’ piece supplied. The ‘T’ has been blanked off using a brass plug. Leave this plug in place. Push the ‘T’ piece firmly onto the water inlet solenoid pipe with the brass plug facing forward. Then push the 15mm cold water supp

Remove as much scale as possible by hand. Dissolve any scale that is difficult to remove by using a de-scaling solution. Remember to replace the drain plug before using the de-scaler. Clean the level sensing probes and their white holders completely using a clean non-metallic scourer. Ensure all traces of de-scaler are removed before using the boiler again. Rather than frequently de-scaling the machine, it may be preferable to install an effective scale reducer or WRAS approved food quality wate

An instruction sheet displayed next to the machine is often helpful in notifying users that the appliance contains and dispense near-boiling water. In line with Health & Safety requirements we recommend that a risk assessment be carried out after the boiler has been installed. It is advisable to display a sign informing customers that drinks made from this boiler are very hot. During normal use of the boiler, certain surfaces will become hot. (especially near to the draw off tap). Care should be

High heat setting Set switches 1 and 2 to ON. All three elements will glow and, when the temperature selected on the electronic control dial 3 is reached, two of the elements will automatically turn off, switching back on if the temperature falls. The fire can be returned to low heat setting by pressing switch 2 to OFF. See also ‘Electronic economiser temperature control ’ below. Electronic economiser temperature control This sensitive output control 3 will switch the radiant heater elements ON

Turning the knob clockwise increases the amount of heat stored. The setting should be adjusted from MIN to MAX to suit seasonal requirements. 2. NEON INDICATOR & 3. FAN SWITCH To obtain heat from the Electricaire Unit press the fan switch to the ON position. The fan indicator light will now glow red. If the fan is controlled by a room thermostat it will switch off automatically when the room temperature reaches the required level. The fan should be switched off before retiring at night. This fun

NOTE ALSO THE INFORMATION GIVEN ON THE HEATER • WARNING - THE SURFACES ON THIS HEATER CAN BE HOT. • This heater meets BS 3456 safety requirements. However, any heater type becomes hot in normal operation. Care must be taken to ensure that prolonged skin contact with the heater does not occur. WHERE YOUNG CHILDREN, INFIRM PERSONS, OR THE AGED ARE LIKELY TO BE LEFT UNSUPERVISED IN THE VICINITY OF THE HEATER WE RECOMMEND THAT A GUARD IS FITTED. Contact your installer or the manufacturer for further

User Note: These instructions give important advice on how to get the best out of your new heater. Please read them carefully and keep them in a safe place for future reference. After Sales Service: Your product is guaranteed for one year from the date of purchase. We undertake to repair or exchange this product free of charge within this period providing the product has been installed and operated in accordance with the manufacturers instructions. Should you require after sales service, please