To reduce the risk of electric shock, do not remove the cover (or back). There are no user-serviceable parts inside. Refer servicing to qualified service personnel. Use of controls or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Industry Canada requirement This class B digital apparatus complies with Canadian ICES-003. Cet appareil n

has Determined that this product meets the ENERGY STAR® guidelines for energy efficiency. (Except DH30E) FOR YOUR RECORDS Write the model and serial numbers here: FOR YOUR RECORDS Write the model and serial numbers here: Safety Precautions.....3 Operating Instructions.................5 Installation Instructions.................8 Care and Maintenance ..............9 Troubleshooting Tips............................10 Warranty.....Back cover Customer Assistance Numbers ....Back cover You can find t

Cleaning the front case bucket and cabinet Clean the front case and the cabinet with a soft cloth, warm water, and a mild detergent. Do not use bleach or abrasives. Cleaning the air filter 1-1. First pull out the air filter by pressing the filter hooks lightly. Then release two tabs at the bottom side of the filter. 1-2. Wash air filter with warm water and a mild detergent. Rinse and dry it. Replace it in place. Cleaning the coil 2-1. Remove air filter from the cabinet regarding to the above. 2-

Power --- Operation starts when this button is pressed and stops when the button is pressed again. Humidity Control --- This button controls the humidity in the room. • : To raise the humidity setting • : To lower the humidity setting • The humidity setting can be set to a permanent "On" setting or to a specific humidity setting between 35% and 70% in 5% increments. "On" setting - dehumidifier runs continuously regardless of humidity condition. 35% - 70% setting - dehumidifier shuts on and off a

Safety Precautions Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

(Refer to Section 2.1.3) 5. Remove the air guide upper. (Refer to Section 2.2.1) 6. Remove the compressor, turbo fan, fan and shroud. (Refer to Section 2.2.2) 7. Remove 2 screws that secure the motor to the motor. (See Figure 10) 8. Remove the motor. 9. Re-install by referring to the procedures above. 2.2.4 AIR GUIDE 1. Disconnect the unit from the power source. 2. Remove the front grille. (Refer to Section 2.1.1) 3. Remove the cabinet. (Refer to Section 2.1.2) 4. Remove the control board. (Refe

INSTALL THE AIR CONDITIONER IN THE WINDOW a. Carefully lift the air conditioner and slide it into the open window. Make sure the bottom guide of the air conditioner drops into the notches of the L bracket. See Figure. 27. IMPORTANT : When the air conditioner drops into the L bracket, the air conditioner will be centered in window opening as shown in Figure. 28. b. While steadying the air conditioner, carefully bring the window sash down behind the upper guide of the air conditioner, as shown in

(1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours Cancel) • The Setting Temperature will be raised by 2°F(1°C) 30min. later and by 2°F(1°C) after another 30 min. -STARTING OPERATION • Everytime you push this button, when the unit is not operating, timer is set as follow. (1Hour 2Hours 3Hours 4Hours 5Hours 6Hours 7Hours 8Hours 9Hours 10Hours 11Hours 12Hours Cancel) POWER • To turn the unit ON, push the button. To turn the unit OFF, push the button again. • Thi

6-4. Remove the hose from the vacuum pump and place it on the charging cylinder. See figure 23B. Open valve C. Discharge the line at the manifold connection. 6-5. The system is now ready for final charging. 7. Recharge as follows: 7-1. Rotary compressor systems are charged from the high-side. If the total charge cannot be put in the high-side, the balance will be put in the suction line through the access valve which is installed as the system is opened. 7-2. Connect the charging cylinder as sho