English Edition Note: If you plan to vent your exhaust hood to the outside, please refer to your range's Owner Installation and Operating Instructions under Exhaust Hood section before completing this installation. Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg elbow added to the exhaust line and 2.5' per 45 deg elbow) Before proceeding, check for damage that may have occurred during shipping. If the contents are damaged, inform the freight company or your dealer immediat

Simply plug the male end of the cabinet power cord into the female receptacle. Plug the stove into wall receptacle. Check all electrical functions of the cabinet (fan,light,clock,etc.) and check again that ALL screws have been tightened before completing the installation. 9

-With a helper, lift cabinet assembly from box by area that is circled. (See Fig. 1 Page 2). -Place cabinet assembly onto stove body. (See diagram above). -Line up holes in the bottom (foot) of the bracket with the stove top holes while one person supports cabinet, fasten the cabinet brackets to the stove with machine screws (2 each side). (See diagram above). -Re-insert screws from the inside of the lip at the back of stove through the splashback , then assemble the nuts and washers to each scr

English Edition Note: If you plan to vent your exhaust hood to the outside, please refer to your range's Owner Installation and Operating Instructions under Exhaust Hood section before completing this installation. Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg elbow added to the exhaust line and 2.5' per 45 deg elbow) Before proceeding, check for damage that may have occurred during shipping. If the contents are damaged, inform the freight company or your dealer immediat

(NOTE: if your cupboards are too low the cresting panel may be left off). 3 ELECTRIC AND COMBINATION STOVES ONLY STOVETOP Gasket - Peel off backing and stick on. Bracket Sheet metaI screw (black) Steel Washer Machine screw (Nickel Plated) Gasket Machine screw Steel washer Sheet metal screw -Remember when working with the cabinet, the cabinet is top heavy. Use your hand to support it during installation. -Place box on the floor close to stove. (See Fig. 1 Page 2). -With a helper,lift cabinet asse

English Edition Note: If you plan to vent your exhaust hood to the outside, please refer to your range's Owner Installation and Operating Instructions under Exhaust Hood section before completing this installation. Note: maximum run of ducting is 25 linear feet (subtract 5' per 90 deg elbow added to the exhaust line and 2.5' per 45 deg elbow) Before proceeding, check for damage that may have occurred during shipping. If the contents are damaged, inform the freight company or your dealer immediat

For Model 9200 use 4 sheet metal screws and washers. To prevent chipping do not overtighten or use power tools. 5 WOOD STOVES ONLY STOVETOP Bracket -Place box on the floor close to stove. (See Fig. 1 Page 2). Machine screw Remove machine screws from the top (2 each side) Screwdriver -Remove the nuts, washers and screws located at rear edge of stove top (2 on SWEETHEART,4 on OVAL) and the 4 machine screws from the stove top. -With a helper, lift cabinet assembly from box by area that is circled.

-Place box on the floor close to stove. (See Fig. 1 Page 2). -With a helper,lift cabinet assembly from box by area that is circled.(See Fig.1 Page 2). -Rest the cabinet assembly on the carton,while your helper steadies the cabinet,peel the cabinet backing off the gasket and stick one on each bracket. -Place cabinet assembly onto stove body.(See diagram above) -Line up holes in the bottom (foot) of the bracket with the holes in the stove top,while one person supports the cabinet, fasten the cabin

-Remove small box and its contents. -Remove the cardboard cross brace. -Remove the plastic wrapped cresting panel. 2 Assembly of Cresting Panel. Main Cabinet Cresting PanelWingnut view of top of cabinet Locate cresting panel packed in bubble wrap. Unwrap the cresting panel and remove the wingnuts. Place the cresting panel on the rear of the top of the cabinet. Take the wingnuts and fasten the cresting panel to the cabinet through the holes at each end of the cabinet. For: WOOD STOVES - go throug

5200, 5210, 4200, 4210, 6200, 6210, 8200, 8210, Exhaust Hood Recptacle Locations When installing the multi-pin plugs, make sure the flat sided pins are aligned with flat sided holes. Each plug is coded for proper fit. Do not force plug into receptacle. Insert themulti-pin plugs into corresponding receptacles- each plug is coded to match its receptacle. Loop power cord on back and attach power cord to stove back with supplied cable tie and screw Plug the stove into wall receptacle. Check all elec