Ask them to read instructions completely. Elite ET100 STROLLER Elite Operating Instructions Important: Read and follow these Safety Rules and Assembly Instructions before operating stroller. If you have any questions concerning the safe use of this product, contact InSTEP LLC at 1-800-242-6110, M-F, 8:00 a.m. - 5:00 p.m. CST or visit our web site at or e-mail us at info@instep.net before using. Safety Rules: WARNING: Failure to follow these warnings and assembly instructions could result in seri

Failure to follow these warnings and assemblynings and assembly · Immediately discard any plastic wrapping. · Never allow children to fold, assemble or disassemble the stroller. · Maximum weight capacity for the Single stroller is 50 lbs. or 22.7 kg. Double 100 lbs. Or 45.4 kg. However, in the DoubleMaximum weight capacity for the Single stroller is 50 lbs.Maximum weight capacity for the Single stroller is 50 lbs. model the weight of 1 child should not exceed 50 lbs.or 22.7 kgs. or 22.7 kg. Doub

Attach the front wheel by loosening the wheel’s Quick Release (Q/R) lever wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight, then flip wheel’s Q/R lever backward to the closed position to lock wheel in wheel’s Q/R lever in open position, hand tighten the cone nut until almost tight,s Q/R lever in open position, hand tighten the cone nut until almost tight, place. Note this step may require minor adjustment until the Q/R lever flips back then flip wheel’s Q/R lever

The front brake operates the same as a bicycle hand brake. Squeeze leverThe front brake operates the same as a bicycle hand brake. Squeeze lever PROPER USE OF SEAT BELTS & SHOULDER STRAPS WARNING: Avoid serious injury from falling or sliding out. Always use seatbelt. Place child in seat. Make sure T-shield is between the child’s legs. When child is seated, place shoulder straps over the child’s shoulders. Pull the back of the seats forward. It will be easier to fold if the seats are not in the r

Step 3. Front Wheel Assembly Turn stroller upright onto its rear wheels, then tip stroller back so the handlebar is down on the ground and the front fork is up.Attach the front wheel by loosening the exterior lock nut on each side of the front wheel far enough to allow the axle and tab washer to slide into the front fork.The tab washer’s tab should be inserted into the small hole on the outside of the front fork (Figure C).Center the wheel between the front C fork.Tighten the nuts with an adjust

Service will be quicker if you have your model number (found on the product and box) along with this instruction sheet ready when calling. If you have any questions concerning the safe use of this product, please contact us immediately. {Figure 1.a} canopy handle locking pin frame parking brake rear wheel foot plate 5K_double_Platform.indd 2 9/26/05 3:50:14 PM Parts List: Description Qty. Frame assembly with seat, canopy, and wrist strap 1 Front Wheel 1 Parent Console (not on all models) 1 Under

WARNING: Child may slip into leg openings and strangle. Never use in a reclined carriage position unless T-shield and shoulder strap have been readjusted to the new seat position. Storage and folding WARNING: Always remove child from stroller before folding Pull the back of the seats forward. It will be easier to fold if the seats are not in the recline position. Remove locking pins from side latches on the stroller frame (Double Models have 2 locking pins). Release the two latches from the fram

Caution: Whenever child is in stroller always use the wrist strap. Before you remove the wrist strap from your wrist make sure you first engage the rear brakes. To Engage Rear Brakes Step on the levers next to the rear wheels until the cogs of the brakes engage the cogs of the wheel. Repeat on other side. To release brake, lift levers using your toe until cogs disengage. To Operate Front Caliper Brake: The front brake operates the same as a bicycle hand brake. Squeeze lever located on handlebar

Lock both plastic latches onto the lower frame, insert locking pin into hole in latch and frame, lock the pin in place by slipping the wire loop over the end of the lock pin. On Double Models repeat for other side. (Figures A1, A2, A3, A4 and A5). A1 A2 A3 A4 A5 Back Rest Handle Rear Frame Latches Side Latch Locking Pin Locking Pin Open Locking Pin Closed Front Fork 2 Step 2. Rear Wheel Assembly Turn stroller onto its side. Grasp rear wheel in one hand, slide wheel’s axle into hole in rear of fr

In the event you notice the stroller veering to one direction, loosen front axle Q/R lever, point the front wheel in the opposite direction the stroller is veering, and retighten the Q/R lever. If you need help making this adjustment, please call our Customer Service department for assistance. Note: If it is necessary to remove the front wheel, you will find it easier to open the brake Q/R lever by taking pressure off the cable. This is achieved by squeezing the brake pads with one hand while ro