Log: The LA220 was engineered in the USA to the highest quality level and will provide you with years of high quality sound level amplification and reproduction. The LA220 utilizes 2 MOSFETS in its design to produce enough voltage to supply the main amplifier and a huge considerable amount of reserve voltage for. peak ’’high demand” situations. © ®®® © c=< C= c= Brtvai ir © 1HMIH C3 a □ a © =3 =3 ©: © Input RCA Jack © Protection LED © Input Level Control Fuse holder © Bridge
SELECT BUTTON Press it can select VOL/BAS/TRE/BAL/FAD, and with the +/- button to adjust them, and the word which function it is selected will be indicated on LCD. 2. POWER BUTTON Press it to select you desired radio band and the word which band is selected will be indicated on LCD. (NOTE: When it is off, you can press any button to turn on the unit.) 3. MANUAL TUNING UP/DOWN BUTTON Press them to tune up or down, and the current frequency appears on LCD. 4. EJECT BUTTON Push it to eject the tape
t % c Q=D(Mll @01= ■CH (u! (u) »™ Ml IE 1 32 u O -± oN) +12V GND REM E Low Level Input Fuse K Gain Controll E 12V (DC) power terminal E Low pass switch ¿6 Remote terminal Low pass cutting adjustment GND terminal S Multiplayer x1/x10 switch for Low section + Left channel terminal (+ MONO) S' Steroe Mono input selector S - Left channel terminal E EBC (External Bass Control) + Rigth channel terminal H EBC ON/OFF switch - Rigth channel terminal (- MONO) s Multiplayer
13 Remote Bass Boost LA-978 2CH amplifier 2 X 100W 2 X 150W 2 X 600W 1 X 1200W 2-4 OHMS 4-8 OHMS 30 A 12.2 X 2 X 13.5 (309 X 53 X 343) 8.2(3.73) LA-1478 2CH amplifier 2 X 125W 2 X 200W 2 X 800W 1 X 1600W 2-4 OHMS 4-8 OHMS 30 A 12.2 X 2 X 15 (309 X 53 X 381) 8.8 (4.0) LA-1878 2CH amplifier 2 X 150W 2 X 225W 2 X 1000W 1 X 2000W 2-4 OHMS 4-8 OHMS 40 A 12.2 X 2 X 17 (309 X 53 X 432) 10.1 (4.62) LA-2078 2CH amplifier 2 X 200W 2 X 300W 2 X 1200W 1 X 2400W 2-4 OHMS 4-8 OHMS 50 A 12.2 X 2 X 19 (309 X 53
Should this occur, the PROTECT LED will be illuminated. At that time, it is important that you check to determine what has caused the protection circuitry to become activated. If the amp shut off because of a thermal overload, allow it to cool down before attempting to restart. If the shutdown occured because of an input overload, or speaker short circuit, be sure to correct these conditions before attempting to restart the amp. To reset the amp, turn the REMOTE power off and on again. 13 Remote
Used properly, these amplifiers will provide you with years of listening pleasure. USER MANUAL table of contents 1~2SPECIFICATIONS 3 LA-478/578/778/978/1478/1878/2078/2278 FEATURES & CONTROLS 4 LA-678/878 FEATURES & CONTROLS 5 LA-2478 FEATURES & CONTROLS 6 ELECTRICAL WIRING, INSTALLATION & SETUP 7 2 CH STEREO INPUT CONNECTIONS 8 4 CH STEREO INPUT CONNECTIONS 9 BRIDGED INPUT CONNECTIONS 11 BASIC STEREO SPEAKER CONNECTIONS 12 MONO-BRIDGED SPEAKER CONNECTIONS 13 MONO BLOCK INPUT & SPEAKER CONNECTIO
They cannot, however tell you the status of a repair, or handle other customer service situations. 1-800-934-2277 Monday through Thursday, 9AM to 5PM Friday 9AM to 2PM Eastern. WWW.legacycaraudio.com Congratulations • Soft turn on/off circuit • Variable gain control • Remote turn on/off • Hi/low level inputs • Power on LED indicator • LED protection indicator • Fully adjustable electronic crossover network • Remote control Bass boost ( 0 – +18dB @ 60Hz ) • 2 ohm stereo stable • Bridgeable into 4
Follow these steps: 1. Set the volume control on your head unit to about the 2/3 position. 2. Adjust the amplifier LEVEL control(s) to an average listening position. LLRR 3. Turn the head unit volume all the way down, and listen for background noise. orange black black 4. Start your vehicle, and again, listen for background noise. 5. By fine tuning the LEVEL control(s), you can reduce background and engine noise, if present. orange These adjustments should only be made once. After that, use the
Try to drive as high a signal level from the head unit as possible. Protection LED comes on when the amplifier ispowered up. • Check for shorts on speaker leads. • Check that the volume control on the head unit is turned down low. • Remove speaker leads, and reset the amplifier. If the Protection LED still comes on, then the amplifier is faulty. Amplifier(s) gets very hot. • Check that the minimum speaker impedance for that model is correct. • Check for speaker shorts. • Check that there is good
Speaker Terminals 1 12 Plug in the Remote Bass Boost Control wire in here. 13 Remote Bass Boost LA-978 2CH amplifier 2 X 100W 2 X 150W 2 X 600W 1 X 1200W 2-4 OHMS 4-8 OHMS 30 A 12.2 X 2 X 13.5 (309 X 53 X 343) 8.2(3.73) LA-1478 2CH amplifier 2 X 125W 2 X 200W 2 X 800W 1 X 1600W 2-4 OHMS 4-8 OHMS 30 A 12.2 X 2 X 15 (309 X 53 X 381) 8.8 (4.0) LA-1878 2CH amplifier 2 X 150W 2 X 225W 2 X 1000W 1 X 2000W 2-4 OHMS 4-8 OHMS 40 A 12.2 X 2 X 17 (309 X 53 X 432) 10.1 (4.62) LA-2078 2CH amplifier 2 X 200W
