Anchor block must be centered on beam and completely welded. 5. Install cylinder onto anchor block with the supplied pin and cotter pins. 6. Log stripper weldment can be welded to the beam or bolted to a 10-gauge (0.1345” thick) plate, which is welded to the beam. If welded to the beam, a 10-gauge spacer must be placed between the log stripper weldment and the beam to get the proper vertical height for the log stripper weldment. The log stripper weldment must rest against the cylinder face to
Assemble, test, and use only in accordance with the Owner’s Manual instructions. READ and FOLLOW chemical label instructions. Pesticides are hazardous chemicals. KNOW emergency procedures BEFORE handling chemicals. Sprayerleaks, bodily chemical contact, poisoning, and spills require immediate response. AVOID inhaling, ingesting, or coming into contact with any chemicals. WEAR personal protectiv e gear w hen filling, using, cleaning, and servicing the sprayer. KEEP sprayer and spray materials aw
Always use two hands for safe operation. 10.) Trigger. Actuate to allow pressurized water to flow out of spray gun. *Note: 157301 shown, location of components on other models vary slightly. Pump Component Identification 11 157300 157301 & 157302 FIG02309 Operation Instructions Water Supply 1.) Make sure the water supply is clean. Debris can cause excess pump wear and reduce performance. 2.) An insufficient water supply will damage your pump. Make sure the water supply is steady and is 20% over
2.) Turn water supply OFF. 3.) Squeeze trigger to relieve system pressure. 4.) Remove garden hose. 5.) Remove pressure hose. Skin puncture hazard. High pressure fluid can inject under skin resulting in serious injury including amputation. Do not direct spray at people or animals. -If skin injection happens, seek IMMEDIATE surgical treatment. -Do not check for leaks with hand. Instead, use a piece of cardboard to check for leaks. -Do not use unit if exterior hose damage is evident. Make sure all
Follow the chemical manufacturer’s recommendations. Understand all safety precautions and first aid for all chemicals. 1. Insert chemical suction line and strainer into a container of detergent. 2. Completely open the chemical control knob located on the chemical injector. 3. Insert the chemical application nozzle (Black). 4. Turn the chemical control knob to adjust the chemical concentration. Spray detergent onto the surface and allow it to soak. Chemicals need time (dwell time) to work properl
Box 1499 Burnsville, MN 55337-0499 1-800-270-0810 NORTH STAR Ranger Pressure Washer HOT- COLD Congratulations on your purchase of the Ranger 157394 Pressure Washer! Your pressure washer is made of high quality components to ensure the top performance you demand. Take the time to read this entire manual so you better understand the machine, how to operate it, the maintenance required and the safety precautions. You will find the assembly, operating, maintenance and troubleshooting instruction
2.) Risk of fire and explosion. Do not add fuel when engine is running or still hot. 3.) Breathing hazard. Poisonous fumes from engine can kill you. Do not operate indoors even if ventilated. 4.) Risk of electrocution. Keep water away from electric outlets and electric devices. 5.) Read owner's manual. Serious injury or death can result if safety instructions are not followed. ©2003 K-Bar Industries 800-270-0810 Part No. 38570 START-UP INSTRUCTIONS 1. Attach garden hose. 2. Attach pressure hose.
-Different chemicals may interact dangerously with each other, always follow chemical manufacturer directions before switching chemicals. -Calculate the correct amount of chemical to mix, dispose of excess chemical per the manufacturer instructions. -Never spray flammable liquids. 6.) Risk of electrocution. Electricity can kill you. Keep water away from electrical outlets and electrical devices. 7.) Flying objects. Small particles may fly out while spraying. Wear safety glasses. Serious eye inju
III.) Before Starting WARNING: Make sure all switches and controls are in the OFF position prior to plugging in the cord. DO NOT stand in water while plugging or unplugging electrical cord. WARNING: Use a UL recognized receptacle protected by a ground fault interrupter and extension cord of proper voltage and amperage at all times. 1. Connect electrical cord to specified NEMA receptacle. See page 4. WARNING: Check hoses, fittings, wand, trigger gun and fuel connections daily for signs of wear, c
-Different chemicals may interact dangerously with each other, always follow chemical manufacturer directions before switching chemicals. -Calculate the correct amount of chemical to mix, dispose of excess chemical per the manufacturer instructions. -Never spray flammable liquids. WARNING strainer diluted chemical pump inlet pump outlet pump 10 Maintenance and Storage Maintenance Mode Before performing any maintenance on the pressure washer, it must be placed in maintenance mode. 1.) Turn off en