DATE TIME – Prints current date and time. 2. DATE YR TIME – Prints current date, year, and time (small font). 3. DATE YR APPD – Prints current date, year, and APPD (approved) message. 4. DATE YR FAXD – Prints current date, year, and FAXD (faxed) message. 5. DATE YR FILE – Prints current date, year, and FILE (filed) message. 6. DATE YR IN – Prints current date, year, and IN message. 7. DATE YR OUT – Prints current date, year, and OUT message. 8. DATE YR PAID – Prints current date, year, and PAID
Remove the Model 3500 / 3700HD / 3000HD from its box and place it on a firm surface. 2. Plug unit into an outlet. 3. Locate key packaged with the unit. Unlock and remove the top cover of the unit. Locate the programming buttons that are labeled SELECT, UP, and DOWN. Place your key in a safe place for future access. 4. STEP 2 – PROGRAMMING THE MODEL 3500 / 3700HD / 3000HD Programming the Model 3500 / 3700HD / 3000HD is extremely easy and can be done in less than 5 minutes. STEP 3 – READY TO GO Re
The manufacturer reserves the right to determine whether the parts failed because of defective material, workmanship, or other causes. Failure caused by accident, alteration, misuse, or improper packaging of returned unit is not covered by this warranty. Any repair to the equipment other than by Pyramid voids the warranty. Users in countries other than the USA should contact the Dealer from whom the unit was purchased. The rights under this warranty are limited to the original user and may not b
The master clock can handle a total of 300 events. An easy to use, plug and play system requires minimal set up time. The bell ringer is available in both 24 VDC and 0-220 VAC format. A one year manufacturer's warranty Pyramid technologies Major Accessories Features is included. Automatic time correction within 2 minutes if power was to fail Automatic Daylight Savings Time adjustment 12 hour or 24 hour display for digital clocks Battery back-up Easy installation Low voltage 24 VDC bel
Employees punch in and out from any Pyramid TimeTrax terminal with the scan of a finger. TimeTrax Bio Ethernet eliminates swipe cards, badges, paper time cards, and costly "buddy punching." Being Ethernet-ready allows for multi-terminal capabilities that will grow with your business. Simply hook the TimeTrax Bio Ethernet unit up to any networked Ethernet jack, and you're on your way. The system accommodates 50 employees and is upgradeable to 6000. TimeTrax Bio Ethernet is the ideal solution to i
LED LEVEL DISPLAY 2. POWER ON/OFF 5. EQUALIZER CONTROL 3. TONE DEFEAT 2 SPECIFICATIONS Input Impedance............ Control Frequencies.......... Control Range.............. Frequency Response.......... Signal to Noise.............. Input Sensitivity for 400mV Output Power Requirement .......... Size..................... 100 Ohm low, 10K Ohm high. 60, 150, 400, 1K, 2.4K, 6K, 15KHz. ± 12dB boost or cut. 20~20KHz. Better than 85 dB (A—Wtd) 2.0 volts low impedance. 200mV high imped
Super Blue amps are some of the most advanced car amplification products available. These quality audio products are designed and engineered to afford you years of uncompromised musical service. Pyramid has utilized the latest electronic technologies in order to deliver a superb listening experience. The Super Blue line has been designed to ensure adequate headroom for even the most demanding peaks and dynamic ranges found on today’s CD’s and recordings. Used properly, these amplifiers will prov
7 2 ch amp PB444X • PB446X • PB449X•4champ PB448X mounting and installation Please read the Installation Precautions section below before installing your Pyramid Super Blue amplifier, and then refer to the diagrams provided to connect power, audio input and speaker connections according to your own system configuration requirements. Installation Precautions • Before you drill or cut any holes, investigate your car’s layout very carefully. Take care when you work near the gas tank, fuel lines, hy
power terminals use these connectors to deliver power, ground, and remote turn-on control to the amplifier. 3 2 ch amp PB446X •PB449X features and controls power LED treble control input gain control low level inputs high level inputs bass control speaker connections power terminals protection indicator bridged mode switch power fuse 4 owner’s manual input gain control use this control to match the outputs of your head unit to the amplifier. Starting with your head unit volume control set at abo
Always test the speakers and their wires first. Amplifier will not power up. • Check for good ground connection. • Check that remote DC terminal has at least +12v DC. • Check that there is battery power on the + terminal. • Check all fuses. • Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. High hiss or engine noise (alternator whine) in speakers. • Disconnect all RCA inputs to the amplifier(s) – if hiss/noise disappears, then plug in the compon