The FAB-1100 is installed in the GI-3821 in accordance with instructions provided with that appliance. NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Factory Supplied Not Supplied with Blower Kit Blower Plug Junction Box ON/OFF Wall Switch 120Vac 60Hz} Factory Supplied Not Supplied with Blower Kit Blower Plug Junction Box ON/OFF Wall Switch 120Vac 60Hz} APPLIANCE WIRING Most appliances are fitted with an electrical "J" box that can be accessed from outside of the appliance outer wrapper at the tim

See Figure 5. Caution! Once the knob is latched, do not move the thumb release until you have completed step 8! Wire Clip Wire Shutoff Plate Figure 6 6. Slide the wire retaining clip onto the wire. Insert the control wire through the hole in the shutoff plate, then slide the clip over the shutoff plate until the clip locks into place. See Figure 6. Handle Grips OFF ON Screen Screen Clips Figure 7 7. Install handle grips onto the handle. It is not necessary to use lubricants to do so. Insert scre

P.O. Box 2810 Tualatin, Oregon 97062 Telephone 503 692-3070 FAX 503 692-6696 75RS75RSTM 2001 Shindaiwa Inc. Part Number 80045 Printed in U.S.A. Shindaiwa is a registered trademark of Shindaiwa, Inc. Part Number 80045 Notes Contents PAGE Introduction ........................................ 1 Assembly ............................................. 2 Operation ............................................. 4 Settings ................................................ 6 Rate Conversion ................

2. Mix fuel with a 2-cycle engine oil designed for use in high-performance 2-cycle air-cooled engines. CAUTION! Some types of gasoline contain alcohol. Never use any type of gasoline containing more than 10% alcohol by volume! More than 10% alcohol by volume may affect the lubricating qualities of 2-cycle engine oils reducing engine life and/or causing engine failure. Generic engine oil and marine engine oil may not be intended for use in high-performance 2cycle engines and should never be use

YES WARNING! Either of the following reactions could cause you to lose control of your saw while cutting, possibly resulting in serious injury! 1. Kickback can occur whenever the guide bar nose or tip contact an object while the saw is running. Tip contact may cause the guide bar to kick upward and back toward the operator, with a lightning-fast reaction! 2. Pinching the saw along the top of the guide bar may push the guide bar rapidly back toward the operator! Pinching can occur whenever wood c

Low depth gauge CHN-05 Cause Wrong gauge setting or no gauge used. Result Rough cutting. Chain grabs. Saw won’t pull chain through wood. Excessive wear on the cutter heel. Remedy If depth gauges are too low, the chain is no longer serviceable. 32 9 DESCRIPTIONMAINTENANCE DESCRIPTIONMAINTENANCE Additional Safety Precautions (cont.) WARNING! ¦ Install the appropriate guide-bar scabbard before transporting the saw. ¦ Never operate a saw that is damaged, improperly adjusted, or not completely and se

See Figure 36. Refer to page 16 for adjustment procedures. Sharpening Instructions (Fig.37) Using a filing gauge Using a depth gauge joiner Using a flat file to round the front corner on a depth gauge Figure 37 IMPORTANT! File all cutters to the same angle and depth! Unequal filing may cause the saw to vibrate or cut erratically! 1. Using a 4.5 mm round file, sharpen all cutters to a 30° angle. Make sure that one fifth (20%) of the file’s diameter is always held above the cutter’s top plate. NOT

n Use medium to higher throttle settings to move grass or leaves from parking lots or walkways. n Use full throttle when moving heavy loads such as dirt or snow. IMPORTANT! Blower noise increases at higher throttle settings! Always use the lowest throttle setting required to get the job done! Wear eye protection that meets ANSI Z87.1 such as a face shield or goggles while operating this machine! Wear close-fitting clothing to protect your legs and arms, and Do not wear clothing or jewelry that c

Muffler Body 48016D First, remove the spark plug Remove the Engine Cover Muffler Screw Retaining Tab Engine Cover Engine Cover 48018 Arrester Screen 5 mm Lower Screw 6 mm Muffler Screws Remove four Allen- head capscrews Figure 15 Gasket WARNING! Never operate the machine with a damaged or missing muffler or spark arrester! Operating with missing or damaged exhaust components is a fire hazard and could also damage your hearing. Exhaust Tube Tail Cap Mounting Screws Figure 16 Remove the Muffler. 1

n LUBRICATION Remove the spark plug, and then pour approximately 1/4-oz of 2-cycle oil into the cylinder through the spark plug hole. Before reinstalling the spark plug, pull the recoil starter gently 2–3 times to distribute the oil over the cylinder walls. n AIR CLEANER Remove, clean, and reinstall the filter element as described under “daily maintenance.” n STORAGE Store the blower in a clean, dry, dust-free environment. CAUTION! Never store this product with any fuel remaining in the tank, fu