The strength of the vacuum can be adjusted by turning the sleeve on the nozzle end. Open the sleeve fully for minimum suction power to vacuum leaves over a garden area. VACUUMING TIPS • Keep the hose straight for best performance. • Rake leaves into the tray at a steady rate so that the engine or motor runs at an even level. For best results, do not cram the tray full of leaves. • Avoid items, such as twigs, that can get caught in the hose. • If material is wet, allow to dry before vacuumin

Push fully in and turn until it snaps into place. NOTE: Insert plug (3) into adapter when vacuum attachment is not in use. See Removing the Vacuum Kit on the next page. 4. Slip the grip (12) onto the handle (11). Putting some soap on the handle will make the grip slide on easier. 5. Connect the handle to the nozzle (6) using the screw (10), washers (9) and nut (8). 6. Connect nozzle (6) or leaf tray (5) to the hose,. 7. Securely place hopper lid (14) on hopper. Ref. Qty. Part No. 1A 1 10

Nos. 1692210, 1692231, 1692353, 9000100 A WARNING Turn off the engine, let the rotor come to a complete stop and disconnect the spark plug wire before assembling the vacuum kit or changing attachments. A WARNING Never remove% adapter from the back of the machine while the machine is running or the rotor is turning. The rotor is pinning just inches away from the adapter iniet. Serious injury will result if you put your fingers or foot in the adapter inlet while the rotor is turning! INSTALL

Only kit. *2480 Adjust vacuum strength by turning ring and adjusting opening size. Figure 1. Kit Parts FORM - 1709566 PRINTED IN U.S.A. 12/93-SMI USING THE VACUUM The vacuum kit lets you take full advantage of the vacuum created by the four fan blades on the rotor flywheel. Placing the lid on the hopper directs the suction power to the hose inlet at the bottom of the housing. Use the vacuum kit to conveniently rake dry leaves and grass clippings into the leaf tray, where the material is s

Place the pivot pin through the blade assembly bracket and push bar. Position the push bar under the tractor front axel and attach it to the axel using two pins and spring clips. Attach the spring end of the lift rod to the push bar assembly and the other end to the tractor lift arm using two spring clips. OPERATION Alternate holes are provided to permit adjustment of the shoe assemblies for raising or lowering the blade when cleaning gravel drives or walks. When cleaning concrete it is desira

No. 209 Mfr's. No.209 Mfr's. No. 203 PACKING The cultivator is packed in one carton disassembled for ease of shipment. ASSEMBLY 1. Attach parallel bars to dravr bar assembly as shown at (1). Lock with Jam nuts so bars are free to swing. 2. Attach depth crank (2) as illusiratod. Adjusting nuts (3) should be equally spaced on threads, 3. Clamp wheel standards to draw bar assembly as shown at (4). 4. Clamp lool holders to tool bar as shown at (5). 5. Attach the lool standards lo the tool

16 x 1" 4 720002 7 Lock Washer, 3/S" 5 717003 7 Hex Nut, Full 3/8"-16 6 107106 2 Shoe Assy. 7 719001 4 Flat Washer, 3/S” 8 720002 4 Lock Washer, 3/8" 9 705004 4 Hex. Cap Screw, 174054 S/8'J-16 x 3/4" 10 1 Pivot Frame Assy. 11 715100 2 Hex Capscrew, l/2”-13 x 1-1/2" 12 717518 2 Hex Nut, 1/2"* 13 13 107116 1 Pivot Plate Assy. 14 722006 2 Cotter Pin 1/8“ x 1" 15 107118 1 Pivot Rod 16 722001 2 Cotter Pin, 3/32” x 3/4" 17 107119 1 Pivot Arm id 156150 1 Spacer 19 705007 1 Hex Capsc

443 12345A7&90 PRIKTeO IN U.S.A. SIMPLICITY MANUFACTURING COMPANY. 1 2 9 U ASSEMBLY The cart enclosure for the vacuum collector consists of a metal framework and a canvas cover, all of which fits on the dump cart body. Here follows step by step illustrations showing the sequence of assembly for this unit« A. The enclosure should be constructed or the cart ■body, starting with the lower channel members shown in Figure 1. The front support assembly la then added as shown In Figure 2. (Refer