1/2006 © 2005 Simplicity Manufacturing, Inc. All Rights Reserved MB 2006-1
Nos. 2690443 & 16948991 MOWER DEFLECTOR INSTALLATION A WARNING Before beginning any service work turn off the PTOj set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). The mower deflector is attached to the deck in its shipping position. Be sure to install it in operating position as shown in the illustration. 1. Remove and retain the hardware securing the deflector to the mower deck. Secure the rear of the rod to the deck using the original hardware. 2. Ins
Make sure all safety guards are in place and all nuts, bolts, clips, cotter pins and wires are secure. 2. Check to make sure spark plug wire is attached. 3. Check all controls for proper operation: a. The engine should stop when the key is removed. b. The fuel shut-off valve should stop the flow of fuel to the engine c. The recoil starter or electric starter (if equipped) should crank the engine when activated. 4. Check the engine area for oil or gasoline leaks. Correct any problems in accordanc
3. Grasp upper speed selector rod (C, Figure 21), and pull up, then tighten the two nuts (A) while maintaining the position of the upper rod. Make sure the shoulders of the carriage bolts are in the slots. 4. Always check traction drive tension and auger drive tension after adjusting speed selector. A A B C Figure 21. Drive Linkage A. Nut C. Upper Speed B. Lower Speed Selector Rod Selector Rod Discharge Control Adjustment If the discharge control is difficult to operate, first lubricate the pini
• Always wear substantial footwear and appropriate winter clothing. Wear foot-ware that improves traction on slippery slopes. DO NOT wear long scarves or loose clothing that could become entangled in moving parts. • Before using, always visually check that all hardware is present, in-tact, and secure. Replace worn or damaged parts. • Never operate the machine with defective guards, or without safety protective devises in place. • Stop engine before: refuelling, removing an attachment, making adj
Cut cable ties (F, Figure 4) that secure control cables to lower handle assembly (C). Be careful not to cut or damage the control cables. Loosen wing nuts (B) and remove any packing materials. Rotate upper handle assembly (A) up. Slide 5/16-18 special bolts (D) through upper handle assembly (A) and lower handle assembly (C). Tighten 5/16-18 locknuts (E) and 5/16-18 special bolts (D). Tighten wingnuts (B), lockwashers (G) and 5/16-18 special bolts (D). D E G A A Figure 4. Un Folding Handle Bars (
No. Description 7800084 I75246E, 7.5HP OHV, Snowthrower 7800085 I7524E, 7.5HP OHV, Snowthrower 7800086 EI75246E, 7.5HP OHV, Snowthrower (CE) 7800087 I7524EX, 7.5HP OHV, Snowthrower (CE) 7800138 EI75246, 7.5HP OHV Snowthrower (CE) ATTENTION SETUP PERSONNEL: The safety warnings provided in this guide and in the operator's manual included with the unit contain important information that must be obeyed when assembling, setting-up, operating, servicing, trans porting, or storing the unit. These warni
No. 1692029 TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE ±10% SIZE SAE GRADE #2 o SAE GRADE #5 © SAE GRADE #8 © 8-32- 19 In. Lbs. 30 In. Lbs. 41 In. Lbs. 8-36 20 99 31 43 10-24 27 99 43 60 10-32 31 99 49 68 1/4-20 66 99 8 Ft. Lbs 12 Ft. Lbs. 1/4-28 76 99 10 14 5/16-18 11 Ft. Lbs 17 25 5/16-24 12 n 19 25 3/8-16 20 tt 30 45 3/8-24 23 n 35 50 7/16-14 30 n 50 70 7/16-20 35 ii 55 80 1/2-13 50 it 75 110 1/2-20 55 ii 90 120 9/16-20 65 it 110
4. Hold adjusting flats (A) and tighten nut (D). 5. Start unit and check auger. Auger must not be engaged unless auger control is depressed. 6. With engine running, fully depress auger control, the auger should engage and run normally. 7. Release auger control. Auger must stop within 5 seconds. 8. If auger does not operate properly, stop engine and recheck drive linkage adjustments. 9. If auger linkage is properly adjusted, auger drive belt tension may require adjustment. See adjusting the auger
. 5 5. Install Chute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6. Install Chute Rotator Crank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7. Tube Handle Levers Cable Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8. Connecting Shift Rod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 9. Chute Rotator Brake Cable Installation. . . . . . . . . . . . . . . . . . . . . .