Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. Refer to Fig. 8-3. 1. 2. 3. a. b. c. 4. 5. Figure 8-6 Figure 8-5 Section 78 — Service 21 Slip the drive belt off the pulley and between friction wheel and friction wheel disc. See Fig. 8-7. Remove and replace belt in the reverse order. NOTE: Engaging the drive control will ease reassembly of the belt. Friction Wheel Inspection If the snow thrower fails to drive with the drive contr

Damage resulting from the installation or use of any part, accessory or attachment not approved by Cub Cadet for use with the product(s) covered by this manual will void your warranty as to any resulting damage. Normal wear parts are warranted to be free from defects in material and workmanship for a period of thirty (30) days from the date of purchase. Normal wear parts include, but are not limited to items such as: batteries, belts, blades, blade adapters, grass bags, rider deck wheels, seats,

731-04870 Spacer, 1.25OD x.75ID x 1.00 Lg. 19. 717-0528A Worm Gear, 20-tooth 44. 618-0123 RH Housing (Incl ref. 45 & 46) 20. 717-0526 Worm Shaft 45. 721-0179 Oil Seal 21. 731-2635 Clean-Out Tool Mount 46. 741-0661A Flange Bearing - RH Housing 22. 731-2643 Clean-Out Tool 47. 618-0124 LH Housing (Incl ref. 45 & 46) 23. 718-04071 Thrust Collar 48. 736-3084 Flat Washer,.51 x 1.12 x.06 24. 790-00087A Bearing Housing 49. 741-0662 Flange Bearing,.75 x 1.0 x.59 25. 721-0325 Grease Plug 50. 741-0663 Flan

The material has been prepared in detail to help you better understand the correct care and efficient operation of your tractor. Before you operate the tractor, study this manual carefully. New copies may be ordered from your dealer at a nominal price. Your local International Harvester dealer is interested in the performance you receive from this tractor. He has factory-trained servicemen, informed in the latest method of servicing tractors, modern tools, and original-equipment IH service part

No. Part No. Description 33 731-0846C Upper Chute 34 714-0104 Pin, Internal Cotter Pin 35 710-04187 Hi-Lo Screw, 1/4-15 x 0.5 36 684-04230 2-Way Chute Control™ Assy 37 731-04954 Steering Control 38 710-04326 Screw, #8-16 x 0.50 39 732-04219A Clutch Lock Spring 40 720-0201A Knob, Crank 41 735-0234 Grommet, Rubber 42 720-04072 Knob, Star, 5/16-18 43 731-04785 Handle Clutch Lock - LH 44 684-04105A Handle Engage Assy - LH 45 784-5594 Cable Bracket 46 747-04263 Eye Bolt 47 736-0231 Flat Washer 48 712

Adjust as follows: (See Figure 32.) 1. Loosen (do not remove) the hex bolt and nut at the stationary idler bracket. 2. Slide the idler pulley upward to tighten the belt. Tighten hex nut and bolt. When no adjustment is left, have belt replaced. 1. Idler Pulley 2. Hex Nut 3. Bolt 4. Drive Belt 21 DRIVE BELT REPLACEMENT If drive belt replacement is required, contact your authorized Cub Cadet Dealer. BATTERY INFORMATION A WARNING A. Battery acid must be handled with great care as conta

If the engine falters, quickly rotate the choke control back toward FULL choke, and then slowly into the OFF position again. 6. When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower. Recoil Starter 1. Rotate choke control to FULL choke position (cold engine start). NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL. 2. Push the primer two or three times for col

You must read, understand and follow all of the directions in this manual as well as the Operator’s Manual before working on this power equipment. CUB CADET LLC, P.O. BOX 361131, CLEVELAND, OH 44136-0019 PRINTED IN USA FORM NO.769-00966 (11/2003) TABLE OF CONTENTS M48 Tank .......................................................................................................... 1 About this Section ............................................................................................. 1 Ch

Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Cub Yellow, the part number to order would be 700-xxxx-0498. Cub Yellow: 0498 Cub Beige: 0499 Powder Black: 0637 17 Model 1333SWE 8 18 Model 1333SWE Ref. No. Part No. Description Qty. Ref. No. Part No. Description Qty. 1 736-0159 Flat Washer .344 ID x .875 OD 7 72 741-0184 Thrust Bearing .88 ID x 1.44 OD x 1 2 710-3015 Truss. Hd. Mach. Scr.

Maintenance Schedule Periodic inspection and adjustment of the engine is essential if high level performance is to be maintained. Regular maintenance will also ensure a long service life. The required service intervals and the kind of maintenance to be performed are described in the table below. Follow the hourly or calendar intervals, whichever occur first. More frequent service is required when operating in adverse conditions. WARNING: If the engine has been running, the muffler will be very h