Those who use and maintain the machine should be trained in its proper use, warned of its dangers, and should read the entire manual before attempting to set up, operate, adjust, or service the machine. MAXIM MANUFACTURING CORPORATION PO BOX 110 • Sebastopol, MS 39359 • WARNING!! Read these and all safety and operating instructions before operating your tiller. Training 1. Read the operating and service instruction manual carefully. Be thoroughly familiar with the controls and the proper use of

If the unit should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. Stop operation when another person approaches. Stop the engine whenever you leave the operating position before making any repairs, adjustment, or inspections. Stop the engine whenever leaving the tiller unattended. When cleaning, repairing, or inspecting make certain tines and all moving parts have stopped. Disconnect spark plug wire and keep wire awa

1 11.15.04 TR PRINTED IN U.S.A. SAFETY RULES SAFE OPERATION PRACTICES FOR WALK-BEHIND POWERED ROTARY TILLERS TRAINING • Read the Owner’s Manual care ful ly. Be thor ough ly famil iar with the controls and the proper use of the equip ment. Know how to stop the unit and disengage the controls quickly. • Never allow children to operate the equipment. Never allow adults to op erate the equipment without proper instruction. • Keep the area of operation clear of all persons, par- tic u larly small chi

1. General questions 1. What is the MAX3420E? 2. Does the MAX3420E include a microprocessor? 3. What packages are available for the MAX3420E? 4. Are the MAX3420E packages lead-free? 2. USB questions 1. What USB speeds does the MAX3420E support? 2. Does the MAX3420E comply with the USB spec? Which revision? 3. How many endpoints does the MAX3420E support? 4. Why doesn't the MAX3420E support isochronous transfers? 5. Can I use the MAX3420E in a self-powered peripheral? 6. Can I use the MAX3420E in

DESCRIPTION The DS21Q55 is a quad MCM device featuring independent transceivers that can be software configured for T1, E1, or J1 operation. Each is composed of a line interface unit (LIU), framer, HDLC controllers, and a TDM backplane interface, and is controlled via an 8-bit parallel port configured for Intel or Motorola bus operations. The DS21Q55 is software compatible with the DS2155 single transceiver. It is pin compatible with the DS21Qx5y family of products. ic.com Note: This Product Pre

Spring 625 461469 1 Depth Bar Adjust. Pin 705 359321 1 Idler Pulley 338009 1 Idler Pulley 706 162069 1 Idler Shaft 708 359325 1 Idler Shaft Arm 709 400290 1 Capscrew NC, 3/8” x 1 3/4” 802 359330 2 Wheel Shoulder Bolt 804 400184 2 Cap Screw, NC 5/16” x 3/4” 805 400186 1 Cap Screw, NC 5/16” x 1” 400190 Cap Screw, NC 5/16” x 1 1/4” 806 400197 1 Cap Screw, NC 5/16” x 2 1/4” 807 400200 4 Cap Screw, NC 5/16” x 2 1/2” 809 400207 2 Cap Screw, NC 5/16” x 3 3/4” 811 400275 1 Cap Screw, NC 3/8” x 3” 813 40

The oil capacity is 20 ounces. 'If not available, a synthetic oil may be used having 5W-20, 5W-30 or 5W-40 viscosity. TO SERVICE AIR CLEANER CARTRIDGE AIR CLEANER Clean cartridge at three month intervals or every 25 hours, whichever occurs first. NOTE: Service more often if necessary. 1. Remove knob and cover. 2. Remove cartridge by pulling it off of the screw. 3. Clean by tapping gently on a flat surface. If very dirty, replace cartridge or clean as follows: a. Wash in a low or non-sudsi

2. To protect against risk of electrical shock, do not put cord, plug, or appliance in water or other liquid. 3. Close supervision is necessary when any appliance is used by or near children. 4. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning. 5. Avoid contacting moving parts. 6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact Consumer Service for examinati

Move lever as illustrated. Figure I I Figure 12 CARBURETOR ADJUSTMENTS (See Fig. 12) Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude and load. 1. To make the initial adjustment: close needle vaive (turn clockwise), then open 1-1/2 turns (counterclockwise). This initial adjustment will permit the engine to be started and warmed up before making final adjustment. 2. Final adjustment is made with engine running at normal operating speed

THOSE WHO USE AND MAINTAIN THE MACHINE SHOULD BE TRAINED IN ITS PROPER USE, WARNED OF ITS DANGERS, AND SHOULD READ THE ENTIRE MANUAL BEFORE ATTEMPTING TO SET UP, OPERATE, ADJUST, OR SERVICE THE MACHINE. SAFE PRACTICES FOR GARDEN TILLERS TRAINING 1. Regard your tiller as a piece of power equipment and teach this regard to all who operate it. 2. Read the owner's manual carefully. Be thoroughly familiar with the controls and proper use of the equipment. Know how to stop the unit and disengage t