Digital voltmeter and ammeter improve accuracy and reliability. Use Model 6075 bus bar sets as needed. [Ë1 ASSOCIATED MODEL 6068 ©æss • « (6068) (6065) USA Model 6065 Parallel Charger Charges 1 to 10 batteries, in parallel, in less than 24 hours. UL listed. 16 charge rates for precise charging. Patented multi-diode rectifier with deep reserve capacity. Use Model 6075 bus bar that includes 10 pairs of charging leads. USA (6086) (6075) Model 6075 Bus Bar Bus Bar set for parallel char

Designed to meet the needs of the most demanding professional with 16 rates of charge and 75 Amp continuous charge with 375 Amps Crank Assist at 12 Volts. 25% more engine start than previous model. UL and CSA listed for indoor and outdoor use. “SAFE IN ANY WEATHER”. (6002 Charger Specilications M0DÜ IS ll M B i R 6001 A 6002 B Jl CON IINUOUS RBTIlUß )00/75 A ■ 100/80 A mnmiiRMiP. RECTIFIER SHIPPING LIMITED DIMENSIONS WARRANT! mmoi 5 Years 5 Years 26"xl6"xl4’ 26"xl6"xl4' 58 lbs

lf the bag becomes dirty aga n very quickly, anolher labric type may be needed. Do nol wash fet labric filler bags which have a sudace coating;genllyr nse lhe coal ng with water SYMPTOM unit w ll nol operate. TroubleshootingChart POSSIBLE CAUSE(S) 1. {mproper electricalconneclon. 2. Blowef wheel loose. 2. Suclion hose too long. 3. Dusl bag dirty. {DONOT REMOVE WHILEUNIT ISRUNNING) 'Tighlen wheel set screws to 165 inch-pounds CORRECTIVE ACTION 1.TurnpowerOFF-asslrreunilis wired per instruclions.

Save these instructions. This manual containsimportant safety, operating and maintenance instructions. INTRODUCTION Model 6065 battery charger is designed to charge one to ten 12 volt batteries in parallel. The multiple charge rates allow batteries to be slow charged or fast charged at a rate not to exceed 30 amps output of the charger. The voltmeter allows you to adjust the charge rate to compensate (see charging instructions). This unit is not intended to be used as a car starting unit. The ou

BATTERY VOLTAGE 6 12 18 24 INITIAL CHARGE RATE SETTING AMPS CHARGE VOLTS CHARGE LO 6V LO 12V LO 18V LO 24V 12V 6V 12V HI LO 2 LO 2 23 4 HI LO HI HI LO 24V 18V 12V CRANK ASSIST VOLTS/AMPS CHARGE 23.6 11.8 5.9 1.110 23.8 11.9 5.95 1.140 24.2 12.1 6.05 1.185 24.8 12.4 6.2 1.225 75% 50% 25% DEAD Open Circuit Voltage 24V Open Circuit Voltage 12V Open Circuit Voltage 6V Specific Gravity STATE OF CHARGE STATE OF CHARGE TABLE Cold Cranking Amps Reserve Capacity Ampere Hours BATTERY SIZE 60 90 350 80+ 10

Never allow the clamps to touch each other. b. When attaching a clamp to a battery post, twist or rock the clamp back and forth several times to make a good connection. This tends to keep the clamp from slipping off the terminals and helps to reduce the risk of sparking. 6. STOP/GO LITE INSTRUCTIONSWhen used properly, the STOP/GO LITE will indicate whether the clamp connections will be correct. Connect the Positive (RED) clamp to the Positive (POS,+) battery post. Touch the contact button of the

To do a hard reset, hold the power button down, press the reset button (hole), wait for the “Palm Powered” screen to show up, then let go of the power button. Press the page-up button to confirm, and the Palm will reset itself. It will prompt you to recalibrate the touch screen. Just follow the directions and when you’ve completed the calibration, your PDA will be ready to use again. Any lost programs can be restored by doing a hotsync, which will put it back to the same condition it was when th

See the section below on Palm Desktop for installation instructions. If both Palm Desktop 4.1 and LS1M Synchronizer are installed, you will see this window appear when you hot- synch: The saved logs will appear in the list. Click on one to get more information at the bottom of the screen. You can also select multiple items by holding down the Control key on the PC keyboard or using the Select All button. You can Delete the selected logs, or use Delete All to delete all saved logs from the PDA. T

The Company hereby warrants to the Purchaser that if the Product, or any part thereof, shall prove to be defective due to improper workmanship or materials at any time up to and including one (1) year from the date of Product's purchase at retail, then the Company shall repair or replace the Product, or any part thereof, as the case may be, at the Company's option, without charge to the Purchaser for parts and labor, provided that Purchaser follows the procedures set forth herein. This limited w

The LS1M Scanner is a scan tool that can retrieve engine parameters and trouble codes from GM vehicle using the VPW OBD-2 protocol. That includes most GM cars & trucks from 1996 to 2006. To verify compatibility of your vehicle to the LS1M scanner, look for the diagnostic connector under the dash, on the driver’s side. It’s a 16-pin connector with pins 1-8 across the top & pins 9-16 across the bottom. The VPW protocol uses pins 2, 4, 5 & 16, so these positions should have a metal insert present.