ADA COMPLIANT Table of Contents Dimensions . . . . . . . . . . . . . . . . . . . . . . .2–3 Rough-Ins . . . . . . . . . . . . . . . . . . . . . . . .4–5Installation Instructions . . . . . . . . . . . . . .6–9 Cleaning and Maintenance . . . . . . . . . . . .10Assembly of Components . . . . . . . . . . . . .11Vernatherm™ Valve Troubleshooting . . . .12Vernatherm™ Valve Repair Parts . . . . . . .13 IMPORTANT Read this entire installation manual to ensure proper installation, then file these instruc

Reassemble the operating rod as shown in Figure 12. Reinstall and adjust so that the foot valve is completely open when the foot lever is fully depressed. This prevents damage to the foot valve due to the absence of the override spring. 3. Turn supplies on and activate the sprayhead. Check piping installation for leaks. 4. Clean the sprayhead if necessary. See page 22 for sprayhead troubleshooting. Adjust the volume control valve, if necessary, to control the flow of water. Figure 12Figure 11 4/

. . Bradley Corporation • 215-1243 Rev. E; EN 08-805 4/24/08 Express® Lavatory System SS-Series SS-2/IR/STD, SS-2/IR/JUV Installation - Obsolete Installation Instructions continued . . . Step 2: Mounting frame to wall 1. Remove the eight Torx-head screws securing the panel to the frame, and remove the panel (see Figure 3). Note: Scuff panel does not need to be removed. 2. Position the frame against the wall, ensuring that it is level. If necessary, insert shims under the frame until level. Note:

• Connect the heat trace cable to the junction box. • Slide the jacket up the side of the tank and pull the drawstring at the top of the jacket. • Place the junction box in the pocket on the inside of the jacket. Figure 1 Back View Bradley Corporation • 215-084 Rev. L; EN 02-586 10-Gallon Tank with Eye Wash and Optional Heater Jacket S19-690LHS, S19-690H Installation Instructions Installation Instructions continued . . . Step 2: Fill tank and pressurize 1. If the tank is pressurized, relieve the

2 Wall Shower Components .................... 2 Wall Shower Dimensions ..................... 3 Step 1: Rough-In Piping ...................... 3 Step 2: Install Shower ........................ 3 Vertical Shroud Installation ................... 4 Horizontal Shroud Installation ................4 Table des Matieres Fournitures requises ......................... 5 Hauteurs de douche conseillees .............. 5 Elements de la douche ......................5 Dimensions de la douche ....................

Main water supply to the unit should be ON at all times. This installation manual and parts list should be filed by the owner’s maintenance department. Installation Instructions WF2605, WF2608 Terrazzo WF2705, WF2708 Stainless Steel Classic Circular 36"/54" Washfountain with Foot Control 215-603 Rev. M; EN 06-915B © 2007 Bradley Corporation Page 1 of 28 4/6/2007 P.O. Box 309, Menomonee Falls, WI 53052-0309 TEL. 1-800-BRADLEY FAX 262-251-5817 Table of Contents Pre-Installation Information . . . .

The hardware, firmware, or software described in this document is subject to change without notice. IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES. Enterasys Networks, Inc. 50

For more than three washfountains, pipe sizes should be increased proportionately. -Supplies from below or through wall - Vented through ceiling off trap inside pedestal Type O Drain -Supplies from above - Vented from below or through wall off drain (mm) Figure 2d NOTE: Supply lines for one to two washfountains should be 1”; for three washfountains, 1-1/4”. For more than three washfountains, pipe sizes should be increased proportionately. Bradley Corporation • 215-1470 Rev. H; EN 06-915 2/8/07 T

The following chart provides details concerning the number of beeps and possible errors associated with them . 1 Beep: Indicates low battery. 2 Beeps: Calibration out of range (environment too reflective). 3 Beeps: Room infrared level out of range; too much sunlight, heat lamp present, etc. 4 Beeps: Solenoid short circuit. 5 Beeps: Solenoid unplugged or loose/broken solenoid connection. Refer to Troubleshooting Chart below and on page 8 for further troubleshooting information. Problem Check Poss

This will continue for 8 minutes and then stop. Proceed to Faucet Operation, page 6. Bradley Corporation •215-1559 Rev. A; EN 04-216A 9/23/04 Aerada 1000 Series Gooseneck Faucet Installation Instructions Faucet Operation Operating Modes • Normal Motion Detecting Mode: water flows within 1/4 second after activating sensor (i.e., putting hands in front of collar) and continues to stay on as long as motion is detected. Maximum time is 45 seconds (factory default setting). • Scrub Mode: water contin