. . . . . . . . . . . . . . . . . . . . . . . . . .go to page 1.1 • Experienced User . . . . . . . . . . . . . . . . . . . . .go to page 2.1 • Expert user . . . . . . . . . . . . . . . . . . . . . . . . . .go to page 2.1 Installers: • Installation . . . . . . . . . . . . . . . . . . . . . . . . . .go to page 2.1 • Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .go to page 2.3 Watlow Controls 1241 Bundy Blvd., P.O. Box 5580, Winona, Minnesota USA 55987-5580 Phone: (507) 454-5300

This new controller can be tailored to perform hardware and software needs with hardware modules that are pluggable and exchangeable and software menus that may be user programmed to fit exact application requirements. With one universal input, a second auxiliary input and four outputs the SERIES 96 can be programmed to perform: temperature measurement, input event switching, remote set point input, heating, boost heating, cooling, alarms, digital communications, ramp and soak and retransmit. Th

BOX 5580, Winona, MN 55987-5580, Phone: 507/454-5300, Fax: 507/452-4507 0600-0008-0000 Rev D $10.00 November 1995 Made in the U.S.A. Supersedes without change: W733-XSMN Rev D00 Contents Contents This manual is a supplement to the Series 733/734 Program Manual. It is for configuring, servicing and calibrating your control. Use this manual in conjunction with the Series 733/734 Program Manual and Data Communications manual. PageItem Chapter 1 3 Install and Wire the Series 733/734 3 Dimensions 3 P

FREEFLEX® heats fluids up to 100°C (212°F) and maintains temperature during transfer from a reservoir to a point of use. In some applications, the tubing can actually serve as the reservoir for limited volumes of fluid, helping to reduce start-up times. For higher temperatures consult the factory. Watlow’s innovative design places the heating element and sensor directly in contact with the perimeter of the tubing to produce efficient, responsive heating and temperature control of the tube conten

Consult your Watlow representative if vertical mounting is unavoidable. • Mount the heater near or below the lowest point on the engine block. Keep outlet nozzle pointed up, as indicated on the tank. Estimate kilowatt requirements with the following formula. First determine the engine displacement, then multiply: English Cubic inches X 3 = estimated wattage Metric Liters X 183 = estimated wattage Outlet Nozzle Sized for 1" I.D. W- 20 Mounting Bolts Vibration Isolator Bushings (2) Mountin

The control mode options include factory selected combinations of ON/ OFF, time proportioning, PI using manual reset and full PID. Input for the Series 160 is a relative humidity/ temperature sensor. Features include mechanical relay outputs, remote setpot, optional remote digital displays, and various cable lengths to accommodate remote sensor location. The Series 160 is also available as a RH/Temperature signal conditioner only, that can be interfaced to other Watlow controls. Specifications

ULTRAMIC 600 heaters are constructed of aluminum nitride (AIN) and incorporate a thermally matched proprietary heating element that provides maximum performance in challenging applications. AIN is especially suitable for applications requiring a clean, non-contaminating heat source. Additionally, the excellent geometric stability ensures consistent part-to-part thermal contact during heating cycles. Watlow AIN heaters can operate up to 600°C with an ultrafast ramp rate of up to 150°C per second

Other voltages are available. Terminals: Non-standard locations are also available. Please specify. Standard Dimensions: ±Xe inch (0.0625 mm) Typical Peak Energy Wavelength: 3-3.5 microns Specifications Heater Dimensions Min. Max. Increments Width: inches (mm) Length: inches (mm) Area: in (cm ) 1 (25.4) 6 (152.4) 6 (38.7) 36 (914.4) 70 (1778) 864 (5574.2) 1 (25.4) any any Note: Less than maximum length X width may exceed maximum area. How to Order To order your stock RAYMAX heater, spe

Now Watlow makes it even easier to install THINBAND heaters with the Quick Clamp option. The flexible one-piece design makes installation on plastics molding equipment faster and easier. Because it can be opened to the full diameter of the barrel without causing internal damage to the heater, the THINBAND heater can be installed on a barrel without removing other band heaters already in place or requiring a more expensive two-piece design. And now with Quick Clamp, the THINBAND can be secured t

The opposite end is sealed to resist contamination. Standard 305 mm (12 in.) flexible lead wires are crimp connected to the terminal pin and have silicone impregnated fiberglass oversleeves. With its round cross-section geometry, the double-ended WATROD is highly adaptable for bending – especially when bending is performed in the field. Both single- and double-ended WATRODs share many construction features that deliver long life—the resistance wire is centered in the heater sheath and electrical