If an adapter is used to accommodate a two-prong receptacle, the adapter wire must be attached to a known .pound. Never remove the third prong. 4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to ж that keys and adjusting wrenches are removed before turning on tool. 5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 6. AVOID DANGEROUS ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep your work area well Illumi

If the end of the rod strikes the table do not change the height adjustment of the saw. Instead, lower the front right side of the table by turning the upper nut on the suspension stud up a few turns. You should now be able to push the front right corner of the table down so the rod indicator can pass over the surface without striking it. 7. Adjust the suspension stud nuts so the top of the table on the front right side just touches the end of the antikickback rod the same as the back. Tighten

Replace cover by lining up holes in cover with holes in the raised sections of the ball retainer assembly. Replace screws and tighten securely (Fig. A13). Fig. A13 2. YOKE CLAMP HANDLE The purpose of this handle is to provide a friction lock between the -upper face of the yoke and the bottom face of the rollerhead. It should also eliminate any play between these two ■ parts. To lock, the handle is 'pushed back from the hand grip of the yoke. If at any time if is possible to move this handle s

Turn the motor “OFF”. Figure K5C Moving the saw back through lb« trough and 1/4-circle kerfs, bring the saw again to the position at the-end of the arm as shown in Figure K5. Tighten Rip Lock and release Yoke Clamp Handle. Turn -motor “ON" and temporarily press the Yoke Locator Pin Handle as you start to rotate the yoke counterclockwise (Figure K5D). Continue rotating until the Locator. Pin stops the yoke, after a 1/4-circie cut, with the blade parallel to the fence. Now, with the motor still

REVIEW SAFETY RULES AND OPERATING INSTRUCTIONS FREQUENTLY. This booklet is provided for your convenience: iw the use ami care of your new DeWalt Saw. These instructions include operation, usage, precautions^ preventive maintenance, maintenance and other pertinent data to assist you in assuring long; life and dependable service from your saw. 700 8" RADIAL ARM SAW No. 7700/3400,120 VOLT, TYPE 5 No. 7700-01,220 VOLT, TYPE 5 Bulletin No. 8814 - INDEX Unpacking, Set-Up..............2-4 Macfii

Set and test the anti-kickback device the same as in RIPPING even though only one of the fingers will take the main “bite”, if needed.-Remember to raise the front, lower blade guard to clear rip fence if needed. Figure §13 20 DADO & PLOUGH CUTS (CUTTING GROOVES) Figure S14 A “Dado” is a grmm mmm the wood grain Ccrosscut) (figure S14). A “Plough" is a groove with the wood grain (rip) (Figure $15). These cuts can be made to any width with a regular saw blade by miking one cut next to another

Si tiene dudas o comentarios, contactenos. 1-877-FNA-GAS1 (1-877-362-4271)•InstructIon ManuaL INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA GuIDe D'utILIsatIon DE GARANTIA. aDVertencIa: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. ManuaL De InstruccIones DH3028 Pressure Washer Laveuse a pression Lavadora a presion 2 English A. Panel assembly B. Nozzle grommets C. Professional spray gun D. Wheel E. Quick-connect spray wand F. Frame G. Engine dipstick/oil plug H. Engine switch I. Sta

HoW to PreVent It • Shut off engine and allow it to cool before adding fuel to the tank. • Use care in filling tank to avoid spilling fuel. Move pressure washer away from fueling area before starting engine. • Keep maximum fuel level 1/2" (12.7 mm) below bottom of filler neck to allow for expansion. • Operate and fuel equipment in well-ventilated areas free from obstructions. Equip areas with fire extinguisher suitable for gasoline fires. 4 • Materials placed against or near the pressure washer

The character that is being changed will be underlined. To move back a character, use the down arrow. To move forward a character, use the up arrow. Basic Operations 8 English 10. Select SET. 11. Choose AM or PM. The up and down arrows AM and PM. 12. Select SET. IMPORTANT: If for any reason the system is disarmed after site still requires protection, the system will need Remote or keypad. The following day, the auto arm will continue to auto arm at the preset time. Disarming the System Deactivat

Questions? See us on the World Wide Web at INSTRUCTION MANUAL INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES GUIDE D’UTILISATION DE USAR EL PRODUCTO. MANUAL DE INSTRUCCIONES DS100 Jobsite Security Portable Alarm System (Base Unit) Systeme d'alarme mobile de securite des chantiers DS100 (Base) Sistema de Alarma Portatil Jobsite Security DS100 (unidad base) i IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US