Log:

Impex IGS-4350

Téléchargements : 3 Taille : 5 mb    Fabricant : Impex  
Catégorie : Formateurs

13 STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of the 87” Butterfly Cable (#42) to the clip on the Right Butterfly (#11). Draw the Cable to the right Swivel Pulley Bracket (#20). B.) Attach a Pulley (#57) to the Bracket. Secure it with one M10 x 1 .” Allen Bolt (#69), two O .” Washers (#66), and one M10 Aircraft Nut (#86). C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating Pulley Bracket (#19). Repeat Procedure B above to install a Pulley

Impex 831.154020

Téléchargements : 4 Taille : 5 mb    Fabricant : Impex  
Catégorie : Formateurs

Do not tighten the Locknuts yet. 12 13 14 15 82 98 98 31 112 36 91 5 91 91 91 26 36 91 112 31 82 98 98 91 91 91 98 98 85 14 14 90 23 23 15 7 6 74—Grease Grease Grease 100 2 5 Arm Assembly 11 16. Attach the Leg Bumper (59) to the Right Seat Frame (3) with an M4 x 16mm Self-tapping Screw (89) and an M4 Washer (96). Grease an M10 x 75mm Bolt (60). Attach the Leg Lever (4) to the Right Seat Frame (3) with the Bolt and an M10 Nylon Locknut (90). Make sure the “U”-rod is on the indicated side of the L

Impex CR 5

Téléchargements : 3 Taille : 5 mb    Fabricant : Impex  
Catégorie : Formateurs

Secure it with one M10 x 2 .” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#5). C.) Draw the Cable underneath the Pulley through the opening on the Right Seat Support (#49) to the open bracket on the Right Base Frame (#46). D.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two . .” Washers (#6), and one M10 Aircraft Nut (#5). E.) Continue drawing the Cable along the Right Base Frame to another open bracket. Install a Pulley as described i

Impex IGS-6900

Téléchargements : 2 Taille : 4 mb    Fabricant : Impex  
Catégorie : Formateurs

Secure it with two M10 x 2 .” Carriage Bolts (#21), one Bracket (#15), two . .” Washers (#27), and two M10 Aircraft Nuts (#28). DIAGRAM 1 5 STEP 2 (See Diagram 2) A.) Slide the Sliding Block (#5) onto the Incline Adjustment Bar (#4). B.) Attach both ends of Incline Adjustment Bar to the open brackets on the Main Frame (#1). Secure each end with one M10 x 2 .” Carriage Bolt (#22), O .” Washer (#27), and M10 Aircraft Nut (#28). C.) Use a Lock Knob (#16) to lock the desired incline position. DIAGRA

Impex IGS-06

Téléchargements : 0 Taille : 4 mb    Fabricant : Impex  
Catégorie : Formateurs

STEP 1 (See Diagram 1) A.) Attach a Floor Stabilizer (#6) and a Lower Pivot Bracket (#35) to the Base Frame (#3). Secure it with two M12 x 4” Carriage Bolts (#28), . 1” Washers (#29), and M12 Aircraft Nuts (#30). B.) Insert the Lower Pulley Bracket (#14) into the hole on the Lower Pivot Bracket (#35). Secure it with one M10 x 1” Allen Bolt (#38) and . 1 .” Washer (#39). C.) Repeat the procedure A and B above to install the other side. DIAGRAM 1 4 STEP 2 (See Diagram 2) A.) Attach a Support Frame

Impex IGS 16

Téléchargements : 0 Taille : 4 mb    Fabricant : Impex  
Catégorie : Formateurs

Align the holes and insert a 8” Bench Press Axle (#44) through the holes. Secure the Axle with two M10 x .” Socket Set Screws (#113). B.) Attach the Bench Press Arm (#1) to the Bench Press Base (#32). Align the holes and insert a 8” Bench Press Axle (#44) through the holes. Secure the Axle with two M10 x .” Socket Set Screws (#113). C.) Thread a T-shaped Pull Pin Set (#69) through the hole on the Bench Press Base (#32) to obtain the desired Bench Press position. D.) Attach two Pulleys (#84) to t

Impex EVE-1500

Téléchargements : 0 Taille : 4 mb    Fabricant : Impex  
Catégorie : Formateurs

G.) Draw the Cable around the Small Pulley then downward to the Selector Rod (#13). Thread the Bolt at the end of the Cable into the Selector Rod. Use the Nut on the Bolt to secure the Bolt into the Rod. 18 DIAGRAM 9 19 STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Attach the 180” Upper Cable (#40) to the front opening on the Right Upper Frame (#4). B.) Place a Pulley (#60) to the opening and secure it with one M10 x 2 3/8” Allen Bolt (#84), two Pulley Bushings (#78), and one M10 Aircraft Nu

Impex AX-PWR7

Téléchargements : 6 Taille : 4 mb    Fabricant : Impex  
Catégorie : Formateurs

Securely tighten all nuts and bolts previously installed. D.) Insert two Weight Posts (#63) to the holes on the Left & Right Supports (#50 & 51). Secure each Weight Post with one M10 x 5/8” Allen Bolt (#88) and ..” Washer (#42). Slide an Olympic Sleeve (#20) onto each Weight Post. Attach a Spring Clip (#22) to the Olympic Sleeve. E.) Insert the Left & Right Bar Holders (#93 & 92) into the selected holes on the Upright Beams. Insert the Left & Right Safety Catches (#58 & 59) into the selected hol

Impex Apex TC-3500

Téléchargements : 8 Taille : 4 mb    Fabricant : Impex  
Catégorie : Formateurs

TC-3500 Durable gray powder coated finish 2 x 23/« inch 14 gauge commercial grade tubular steel construction Unique multi-use Lat Pull/Chin up/ Pull up bar with no head restrictions Special angled VKR arms, pads and handles for proper arm, hand and body placement Angled Dip handles allow for greater arm and chest exercises Angled upright ensures full Knee lift pre-stretch Elevated push up handles for full range of motion exercises Ab crunch foot hold down foam roller pads Comfortable

Impex EVE-725

Téléchargements : 1 Taille : 4 mb    Fabricant : Impex  
Catégorie : Formateurs

THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for





catégories