The package contains three sets of crimping dies. Each set of dies is designed for different connectors and their marking and application are shown in the following table. Die Marking Cavity Marking Application BC/ST .151 ST* (BAYONET), FC-1, BICONIC .178 TECS (SMA) 200/230 .213 PROTECTIVE COVER-8500 SC sPLICE SC and FC-3 .120 2.4mm CABLE CRIMP RING .137 3.0mm CABLE CRIMP RING .190 KEVLAR CRIMP AREA PPST ST ( PUSH PULL) .120 2.4mm CABLE CRIMP RING .137 3.0mm CABLE CRIMP RING

Never attempt your own repairs. 3. Do not drop the monitor or expose to strong impacts. 4. Do not expose to direct sunlight for extended periods of time. A -2- Monitor Setting The color display is equipped with OSD prompting for the monitor settings. All settings must be changed using the remote control. Invoking the OSD: 1. Remove the remote control from the cradle. 2. Press the - and + buttons at the same time. 3. The OSD menu "Monitor Settings" is displayed. 4. In the OSD menu, you

Installing the Noise Reduction board into the 3M Base Station 1. Remove the right-hand and left-hand top covers from the 3M base station. Be careful that the main circuit board does not fall out of the plastic base. 2. See ***Important installation notice*** on next page before performing this step. Plug the A125 ribbon cable onto connector J8, located at the top of the left side of the circuit board. Be careful to support the rear side of the base station circuit board when plugging in the A125

EXPLANATION OF GRAPHIC SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are capable of producing an electric shock . The exclamation point within a triangle is intended to alert the user that important operating and ser

Power On LED Indicator 2. Power On/Off Switch 3. Remote Control Sensor 4. Picture Select 5. On Screen Adjustment Up Button 6. On Screen Adjustment Down Button 4 REAR PANEL 7 9 8 10 7. Power Input Connector: Red = +12 VDC Black = ground 8. Video Signal Input Connector 9. IR Repeater Connector 10. IR Repeater Transmitter NOTE: This cable (10) is utilized to connect to Video Cassette Players that do not accept the IR Repeater 1/8" (3.5mm) style plug (9). The IR Repeater Transmitter is provided with

Replace the battery when the “Lo Batt” indicator shows in the display. Long life alkaline batteries are available from Fluke Biomedical. Any standard 9 V alkaline battery can be used in the Digital X-Ray Pulse Counter/Timer. To replace the battery, slide open the battery compartment on the bottom of the case. Remove the old battery, and install the new battery. Operation General Instructions Section 2 Operation 2.1 General Instructions Switch Settings The front panel selector/toggle switch on th

Fitting Instructions Must be followed each time respirator is worn. Fig.1Fig. 2 Fig. 3 Fig. 4 1. Cup the respirator in your hand, with the nosepiece at your fingertips, allowing the headbands to hang freely below your hand. 2. Position the respirator under your chin with the nosepiece up. Pull the top strap over your head resting it high at the top back of your head. Pull the bottom strap over your head and position it around the neck below the ears. 3. Place your fingertips from both hands at t

See insert for approval label. 1 This respirator helps protect against certain particles. Misuse may result in sickness or death. For proper use, see supervisor, or User Instructions, or call 3M in U.S.A., 1800- 247-3941. In Canada, call Technical Service at 1-800-267-4414. IMPORTANT Before use, wearer must read and understand these User Instructions. Keep these instructions for reference. Use For Solids such as those from processing minerals, coal, iron ore, flour, and certain other substances.

IR Repeater Connector 10. IR Repeater Transmitter 11. Audio Right Channel Input Connector 12. Audio Left Channel Input Connector 5 Note A : This cable (10) is utilized to connect to Video Cassette Players that do not accept the IR Repeater 1/8" (3.5mm) style plug (9). The IR Repeater Transmitter isprovided with an adhesive that allows it to adhere toVideo Cassette Player remote sensor. Remove thebacking covering the adhesive and place the IR Repeater Transmitter directly over the Video CassetteP