while ffrmiy puiiinq ism out the rea^ of îne ¡am:nator Ciontmue pi;* .iH'j the Mrr u.nt-i : ijfVA.nor>completely from the rotie's At ihis point you w^i iee ^ rnorr.^ni^'y lightening o* tension, to* owed r;y a si-o^g i>-:i m the opposite ejection 3 Release the reverse swuch. an^ r.jn tnt1- ia^ nator forward cntil ai* wnnk.ed filrr* exit^out t*v- rear NOTE: If film is wrapped arourvj the pultrolier!, does not extend out the rear of the larnnatof re^vicw the top iiim supply roll, and pofi the

Remove 4 book supports from storage compartment, lb. Insert support #1 firmly in front slot. Firmly insert remaining supports in consecutive numerical order. 2a. Plug in and switch on 250T. The yellow wait light will illuminate. 2b. In about 4 minutes a "beep" will sound and the green light will iluminate. At this time the 250T is ready for binding. BOOK PREPARATION 3. Firmly hold sheets to be bound and place binding edge on lined surface. The first horizontal line above the paper will indic

L’AVERTISSEMENT SUIVANT SE TROUVE AU BAS DU PRODUIT. Ce message de securite signifie que vous pourriez etre gravement blesse ou tue si vous ouvrez ce produit et vous exposez a une tension dangereuse. CONSEILS DE SECURITE IMPORTANTS CONSEILS DE SECURITE GENERAUX • N’utilisez l’appareil que pour l’usage prevu. • Ne mettez dans l’ouverture de l’appareil que des pochettes/documents. • Placez l’appareil sur un plan de travail stable et bien fixe afin d’eviter que l’appareil ne tombe et risque de caus

Electrical safeguards • The unit must be connected to a supply voltage corresponding to the electrical rating shown on the unit. • Unplug the unit before moving it, or when it is not in use for an extended period of time. • Do not operate with a damaged supply cord or plug. Do not alter the attachment plug. The plug is configured for the appropriate electrical supply. • Do not overload electrical outlets beyond their capacity; fire or electrical shock could result. • The unit is intended for ind

• If the laminated item is wavy, the TEMPERATURE is too hot. Verify temperature selector is set at the appropriate temperature. • Always allow sufficient time for the laminator to adjust to changes in temperature setting. The inside of the laminator will glow green when the laminator has reached operating temperature. Position the document to be laminated into a GBC laminating pouch, so that the document is aligned to the folded sealed edge and the right and left borders are equal and insert the

1. Select a GBC No-Heat Laminate that is slightly larger than the document to be laminated. 2. Run the film, film-side faced up, for about 3-6mm (1/8 1/ 4”) into the laminator, and then press OFF to stop the rollers. 3. Carefully separate the backing release paper from the film, and drape the clear film over the top of the laminator. 4. Place the document between the separated film and backing. Turn the power switch to RUN. 5. After the laminated document exits the rear of the laminator, then ei

laissez-la refroidir avant de esperar una tiempo antes de Kaltlamination beginnen, eine angemessene Zeit warten, damit sich das Gerat abkuhlen kann. 1. Selecteer een GBC No-Heat plastificeerfilm die iets groter is dan het te plastificeren document. commencer la plastification a froid. 1. Selectionnez une pochette G.B.C. speciale plastification empezar el proceso frio. 1. Escoger una pelicula para plastificar en frio ligeramente mas ancha que el documento 1. Wahlen Sie ein GBC-No Heat Laminat fur

Handle carriers carefully so they may be re-used. 3. insert the folded edge of the carrier STRAIGHT into the front of the laminator until you feel the rollers grab the carrier. 4. Remove the carrier from the rear of the GBC DocuSeal 120 after it has stopped moving. Leave the pouch within the carrier for a few seconds to cool before removing it. Removing it too soon may distort the lamination. 5. When you are finished laminating for the day switch the machine to “OFF”. ELECTRICAL SAFEGUARDS

The shredding of other metal items will damage the cutting blades. Plastic materials such as charge cards, covers, inserts and film may be shredded on a very limited basis However, extended shredding of such materials will prematurely dull the cutting blades The shredder control panel is shown in Figure 4-1. To start shredding, press the "ON" button then feed the material to be shredded into the throat of the shredder. Never exceed the maximum capacity of the shredder To tum the shredder off pr

1 - 1 Section 2: Warranty Limited warranty information ..................................................... 2 - 1 Exclusions to the warranty .......................................................... 2 - 1 Section 3: Specifications Section 4: Installation Uncrating ........................................................................................4 - 1 Uncrating Diagram........................................................................4 - 2 Electrical Requirements.....................