Solution: Slowly turn Beer Flow Control Handle to ON position. Problem: Beer does not flow after keg is tapped. Probable Cause: Universal Empty Keg Sensor has locked up. Solution: Turn Beer Flow Control Handle to OFF position. Wait two or three seconds than slowly turn Beer Flow Control Handle to ON position. Probable Cause: Beer Flow Control Handle is OFF. Solution: Slowly turn Beer Flow Control Handle to ON position. Probable Cause: Universal Empty Keg Sensor is dirty. Solution: Clean Universa

40000B Piston Party Pumps Sturdy and easy to use. Has palm-sized handle to pump more air with less effort. Red thermoplastic cylinder; all metal coupler. Convenient vent button to control foaming. Includes two foot vinyl hose with nylon faucet. Easy to disassemble for cleaning. Packed in individual display cartons, 25 per case. Ship Weight: 25 oz. each For Single Valve Kegs Part No. 40000B For Imported Kegs Part No. 40025B Bellows Party Pump Unique polyethylene bellows seals out grit. No

Probable Cause: Solution: Beer Flow Control Handle is in CLEAN position. Slowly turn Beer Flow Control Handle to ON position. Problem: Beer does not flow after keg is tapped. Probable Cause: Solution: Smart Coupler has locked up. First, turn Beer Flow Control Handle to OFF position then turn Beer Flow Control Handle to CLEAN position. Wait five seconds then turn Beer Flow Control Handle to ON position. Probable Cause: Solution: Beer Flow Control Handle is OFF. Turn Beer Flow Control Handle to CL

Slowly turn Beer Flow Control Handle to ON position. Problem: Beer does not flow after keg is tapped. Probable Cause: Solution: Smart Coupler has locked up. First, turn Beer Flow Control Handle to OFF position then turn Beer Flow Control Handle to CLEAN position. Wait five seconds then turn Beer Flow Control Handle to ON position. Probable Cause: Solution: Beer Flow Control Handle is OFF. Turn Beer Flow Control Handle to CLEAN position. Wait five seconds then turn Beer Flow Control Handle to ON

Use of 8 oz glasses is recommended to maintain the ideal serving temperature. Draught and Drink * Be aware that the first glass you pour from every new DraughtKeg will contain mostly foam. This is typical of draught beer. Allow the foam to settle and continue to pour. * Tilt and pour: Tilt your glass at a 45 degree angle as you pour and adjust upright as the glass fills. * Ensure you pull the tap handle all the way down. Not opening the handle all the way will result in excessive foam. * For the

It senses when a keg is empty and shuts off the beer flow, yet leaves the line fully charged with beer. This prevents gas from entering an empty line causing excessive foaming when tapping a fresh keg. Packed 25 per case. Weight: 1 lb. 8 oz. each Part No. Description 26000F*...............................For Domestic Kegs 27500F.................................For Imported Kegs *U.S. Patent #5,630, 441 Universal Empty Keg Sensor Controls the amount of beer loss by closing off the beer flow

Screw connector to stainless steel beverage line on faucet standard. Tighten with a wrench, but do not over tighten. 2. Make sure lever handle on keg coupler is in the UP (untapped) position. Place one brown leather washer into wing nut end of black beer line connector hose and thread onto top of keg coupler. Hand tighten. 3. Place clamp on one end of red air line. Push end over air valve located inside cabinet. Tighten clamp with screwdriver. Turn shut-off valve to OFF (horizontal) position. 4.

Adjusting CO2 Gas Flow 1. Turn regulator adjusting screw counterclockwise until it turns freely. 2. Turn hand valve counterclockwise on CO2 cylinder to the fully open position. 3. Turn regulator adjusting screw clockwise until desired pressure is reached (approx. 12-15 lbs.). Tighten stop nut on adjusting screw. 4. Open shut-off valve on bottom of regulator. CO2 Leak Test Shut Off Valve (Black Lever in Closed Position) Cover for Adjusting Broach Regulator Fitting Fitting for Red Air Hose Dilute

Electrical The cabinet must be connected to a separately fused power source (see electrical specification plate) and grounded in accordance with National and Local Electrical Codes. Caution: Do not attempt to operate the equipment on any other power source than that listed on the Electrical Specification plate. IMPORTANT WARNING To avoid compressor damage. DO NOT RUN UNIT IF CABINET HAS BEEN LAID ON ITS BACK If cabinet has been laid on its back for any reason, place it back into the upright posi

INSTALLATION AND OPERATION INSTRUCTIONS FLAT TOP BOTTLE COOLER Table of Contents Cabinet Specifications ..........................................2 Installing Uncrating and Inspection ................................3 Plumbing .........................................................3 Electrical..........................................................3 Adjusting Partitions .........................................3 Installing Casters and Legs.............................3 Placing the Cabinet...